109 HYDRAULIC RESERVOIR REF NO. PART NUMBER QTY DESCRIPTION REMARKS NOT SHOWN: FOOTNOTES: 1. ARRANGE LINER PADS IN AN EVEN PATTERN ON THE INTERIOR SURFACES OF THE SIDE PLATES AND KICK PLATE. USE .12" THK AND .25" THK TO PROVIDE A SNUG FIT FOR THE TANK. APPLY AND ADJUST THE LINER PADS UNTIL THE LEAST MOVEMENT POSSIBLE HAS BEEN OPTAINED. 2. REFER TO PAGE "BATTERY HOLD DOWN" FOR BATTERY INSTALLATION DETAILS. THE TANK SHOULD NOT SHIFT WHEN FILLED. 3. ORIENT PADLOCK LUGS AWAY FROM STAIRWELL. 4. MORE THAN ONE SUPPORT MAT (117-442) MIGHT BE REQUIRED WITH DUAL BATTERY INSTALLATION, OR, POSSIBLY TO OBTAIN A SECURE FIT FOR SINGLE BATTERY INSTALLATION. 5.
SCREWS (105-214) REPLACE SCREWS (107-781) THAT COME WITH FILL NECK FLANGE. NOTE: REF #1, FILL NECK (364-632) INCLUDES LOCKABLE CAP 153-760, FLG GASKET 153-607, & STRAINER BASKET 153-606. REFER TO F/N 5 . 04 ID0136836 1 364-632 1 FILL NECK SEE F/N 3 & 5. REFER TO NOTES BELOW. 2 105-214 6 FLG SCREW (#10-24 X .5") SEE F/N 5 3 320-657 1 BATTERY COVER 4 117-442 1 SUPPORT MAT "USE AS REQUIRED". SEE F/N 4 5 334-003 1 BATTERY COVER 6 364-633 1 HYDRAULIC RESERVOIR (75) REFER TO REF. #23.
7 307-311 1 HYDRAULIC TANK STEP 8 320-591 1 CRADLE WELDMENT 9 157-466 1 DRAIN PLUG (1-UNF, .375 ORF) 10 500-749 1 O-RING (211 D70) 11 214-854 1 TEMPERATURE SWITCH(1/4NPT,MALE) 12 322-289 1 BACKUP (BOLT-ON) 13 110-411 1 BOLT-ON CLAMP (3/4", SET) 14 105-818 2 BOLT (1/4-NC X 1-1/2") 15 111-021 1 BREATHER CAP (TANK) 16 116-322 1 BULK HOSE (1/2", SOLD PER 1") USE 1 @ 48" 17 110-217 1 WORM CLAMP (7/16" TO 1") 18 156-108 1 S/O COUPLER (08N-08H90) 19 105-829 6 FLG LK BOLT (1/2-NC X 1") 20 105-833 2 FLG LOCKNUT (1/2-NC) 21 106-387 9 FLG LOCKNUT (M10-1.50) 22 106-558 5 CLIP NUT (M10-1.50) 23 121-040 1 SIGHT GLASS 24 107-096 2 LOCKNUT (M8-1.25, NLK) 25 117-425 AR LINER PAD (.12" THK) SEE F/N 1.
ALSO USE AS NEEDED 117-463 (.25' THK PAD) 26 105-095 2 WASHER (1/4") 27 313-908 1 RIGHT AIR DEFLECTOR 28 514-446 1 REDUCER (24S-20SF) 29 106-724 8 FLG SCREW (M10-1.50 X 25MM) 30 105-033 1 BOLT (5/16-NC X 2") 31 110-333 1 BOLT-ON CLAMP (1") 32 105-831 2 FLG LK BOLT (1/2-NC X 1-1/2") 33 106-382 2 FLG LK SCREW (M10-1.50 X 20MM) 34 107-334 2 SCREW (M8-1.25 X 25MM,BUT SOC) 35 107-001 4 FLG LK SCREW (M10-1.50 X 25MM) 36 319-452 1 CONNECTOR PLATE