Komatsu — TIGHTENING TORQUE LIST

. MAINTENANCE TIGHTENING TORQUE SPECIFICATIONS TIGHTENING TORQUE SPECIFICATIONS TIGHTENING TORQUE LIST CAUTION Apply the following table for Hydraulic Hose. 4 - 12 If nuts, bolts, or other parts are not tightened to the specified torque, i t wil l cause looseness or dam age to the tightened part s, and this wil l cause failure of the machine or problems with operation. Always pay careful at tentio n when tightening parts Unless otherwise s pecifi ed, tighten the metric nuts and bolts to t he torque shown in th e table below. If it is n ecessary to replac e any nut or bolt, always use a Komatsu genuine part of the sa me size as the part tha t was replaced.

Thread diameter of bolt (a)(mm) Width across flats (b)(mm) Tightninig torque [Nm (kgm)] Target value Permissible range 6 8 10 12 14 10 13 17 19 22 13.2 (1.35) 31 (3.2) 66 (6.7) 113 (11.5) 177 (18.0) 11.8 - 14.7 (1.2 - 1.5) 27 - 34 (2.8 - 3.5) 59 - 74 (6.0 - 7.5) 98 - 123 (10.0 - 12.5) 157 - 196 (16.0 - 20.0) 16 18 20 22 24 24 27 30 32 36 279 (28.5) 382 (39.0) 549 (56.0) 745 (76.0) 927 (94.5) 245 - 309 (25.0 - 31.5) 343 - 425 (35.0 - 43.5) 490 - 608 (50.0 - 62.0) 662 - 829 (67.5 - 84.5) 824 - 1030 (84.0 - 105.0) 27 30 33 36 39 41 46 50 55 60 1320 (135.0) 1720 (175.0) 2210 (225.0) 2750 (280.0) 3280 (335.0) 1180 - 1470 (120.0 - 150.0) 1520 - 1910 (155.0 - 195.0) 1960 - 2450 (200.0 - 250.0) 2450 - 3040 (250.0 - 310.0) 2890 - 3630 (295.0 - 370.0) 42 65 3830 (390.0) 3430 - 4220 (350.0 - 430.0) Nominal - No.

of threads (a) Width across flats (b) (mm) Tightening torque Target value Permissible range Nm kgm lbft Nm kgm lbft 9/16 -18UNF 19 44 4.5 32.5 35 - 63 3.5 - 6.5 25.3 - 47.0 11/16 -16UN 22 74 7.5 54.2 54 - 93 5.5 - 9.5 39.8 - 68.7 13/16 -16UN 27 103 10.5 75.9 84 - 132 8.5 - 13.5 61.5 - 97.6 1 -14UNS 32 157 16.0 115.7 128 - 186 13.0 - 19.0 94.0 - 137.4 13/16 -12UN 36 216 22.0 159.1 177 - 245 18.0 - 25.0 130.2 - 180.8