. MAINTENANCE OUTLINES OF SERVICE 4 - 5 FUEL To prevent the moisture in the air from co ndensing and forming water inside the fuel tank, alway s fill the fue l tank after completing the day's work. and if fuel containing water or dirt is used, it cannot work properly. get in when storing or adding fuel. ation and Maintenance Manual.
The fuel pump is a precision instrument, and if fuel containing water or dirt is used, it cannot w ork properl Be extremely careful not to let impurities Always use the fuel specified in the Oper Fuel may congeal depending on the tem perature when it is used (particularly in low temperatu res below - 15 ° C (5°F)), so it is necessary to use the fuel t hat is suitable for the temperature. Before starting the engine, or when 10 mi nutes have passed after adding fuel, drain the sedimen t and water from the fuel tank. If the engine runs out of fuel, or if the filte rs have been replaced, it is necessary to bleed the air from the c ircuit. NOTICE . Always use diesel fuel.
Never use any other fuel The engine on this machine uses electronic cont rol and high-pressure fuel injection equipment to enable it to provide goo d fuel consumption and good exhaust gas characteristi cs. For this reason, high-precision parts and lubricating abil ity are demanded. Using low-viscosity fuel with poor lubricating abi lity will cause a marked reduction in the durability of the eng ine. COOLANT AND WATER FOR DILUTIO N preventing corrosion as well as preventing freezing. n issue, the use of antifreeze coolant is essential. matsu Supercoolant (AF-NAC).
Komatsu Supercoolant (AF-NAC) has The coolant has the important function of Even in the areas where freezing is not a Komatsu machines are supplied with Ko matsu Supercoolant (AF-NAC). Komatsu Supercoolan t (AF-NAC excellent anticorrosion, antifreeze and co oling propertiesand can be used continuously for 2 year s or 4000 h ours. Komatsu Supercoolant (AF-NAC) is stro ngly recommended wherever available. distilled water or tap water (soft water).
well water (hard water), contains large amounts of minerals (calcium, When diluting the antifreeze coolant, use Natural water, such as a river water or (calcium, magnesium, etc.), and this makes it easie r for scale to form inside the engine or radiator. Once s cale is deposited inside the engine or radiator, it is extre mely difficult to remove. It also causes overheating d ue to poor heat exchange, so when you dilute the coolan t, we recommend that you use water with an overall hardness of less he precautions given in the Operation and Maintenance Manual. re to keep it away from flame. ater differs according to the ambient temperature. "CLEAN INSIDE OF COOLING SYSTEM (PAGE 4-22)".
already mixed. In such cases, never dilute with water. ne to cool before adding coolant. hardness o f less than 100 PPM. When using antifreeze, always observe t he precautions given in the Operation and Maintenan ce Manual. Antifreeze coolant is flammable, so be su The ratio of Supercoolant (AF-NAC) to w For details of the ratio when mixing, see "CLEAN INSIDE OF COOLING SYSTEM (PAGE 4-2 Supercoolant (AF-NAC) may be supplied already mixed. In such cases, never dilute with wate If the engine overheats, wait for the engi If the coolant level is low, it will cause over heating, and will also cause problems with corrosion d ue to air entering the coolant. GREASE oises at the joints.
er heavy-duty conditions. Always use the recommended grease and Grease is used to prevent seizure and n This construction equipment is used und follow the change intervals and recomme nded ambient temperatures given in this Operation a nd Maintenance Manual. Grease fittings not included in the maint grease. enance section are grease fittings for overhaul, so they do not need for long time, add grease. is pushed out when greasing. If any part becomes stiff after being used Always wipe off all of the old grease that Be particularly careful to wipe off the old grease in places where sand or dirt sticking in the grea se would c ause wear of the rotating parts.