John Deere 310G Tractor Backhoe Parts Manual

Contents

310G,310SG and 315SG BACKHOE LOADERS PARTS CATALOG 310G,310SG and 315SG BACKHOE LOADERS PC2755 (Jan-07) English Worldwide Construction and Forestry Division Worldwide Edition Litho In U.S.A.(Revised) COPYRIGHT © 2007 DEERE & COMPANY Moline, Illinois All rights reserved

Page 1

Contents

000I-1 310G, 310SG AND 315SG BACKHOE LOADERS INTRODUCTION AND CUSTOMER INFORMATION T134142 -UN-10OCT00 SIDE VIEW OF JOHN DEERE BACKHOE LOADER (MANUFACTURED 2000- ) TO THE CUSTOMER THE PART NUMBERS IN THIS PARTS CATALOG WERE CORRECT AT THE TIME YOUR CATALOG WAS PUBLISHED. IT IS OUR POLICY TO CONSTANTLY IMPROVE OUR MACHINES AND, THEREFORE, PART NUMBERS MAY CHANGE. WHEN ORDERING PARTS, VERIFY PART NUMBERS THROUGH YOUR DEALER’S (SPECIFICATIONS AND DESIGN SUBJECT TO CHANGE WITHOUT NOTICE.) 310G, 310SG AND 315SG BACKHOE LOADERS PC2755 (14-SEP-06) 000I-1 PN=1

Page 3

Contents

000I-2 310G, 310SG AND 315SG BACKHOE LOADERS SERIAL NUMBER LOCATIONS EACH 310G, 310SG AND 315SG BACKHOE LOADER HAS SIX SERIAL NUMBERS, A PRODUCT IDENTIFICATION NUMBER PLATE, AN ENGINE SERIAL NUMBER PLATE, A HYDRAULIC PUMP SERIAL NUMBER PLATE, A MFWD AXLE SERIAL NUMBER PLATE, A TRANSMISSION SERIAL NUMBER PLATE, AND A REAR AXLE SERIAL NUMBER PLATE. THE PRODUCT IDENTIFICATION NUMBER IS ON THE LEFT-HAND SIDE OF THE LOADER FRAME JUST ABOVE THE LIFT CYLINDER PIVOT BOSS. THE ENGINE SERIAL NUMBER PLATE IS LOCATED ON THE RIGHT-HAND SIDE OF THE CYLINDER BLOCK NEAR THE FUEL PUMP. THE MFWD AXLE SERIAL NUMBER PLATE IS LOCATED ON THE RIGHT-HAND (REAR) SIDE OF THE MFWD AXLE HOUSING.

THE REAR AXLE SERIAL NUMBER PLATE IS LOCATED ON THE RIGHT-HAND (FRONT) SIDE OF THE AXLE HOUSING. THE TRANSMISSION SERIAL NUMBER PLATE IS LOCATED ON THE BOTTOM-REAR FACE OF THE HOUSING. THE HYDRAULIC PUMP SERIAL NUMBER IS LOCATED ON THE BOTTOM FACE OF THE PUMP. LEFT-HAND SIDE, RIGHT-HAND SIDE, FRONT AND REAR OF THE BACKHOE LOADER ARE VIEWED BY FACING IN THE DIRECTION OF THE BACKHOE LOADER FORWARD TRAVEL. LEFT-HAND SIDE, RIGHT-HAND SIDE, FRONT AND REAR OF THE BACKHOE COMPONENTS ARE DETERMINED WHEN SEATED IN THE BACKHOE OPERATING POSITION. IF PRODUCT IDENTIFICATION NUMBERS OR SERIAL NUMBERS ARE REQUIRED FOR WARRANTY CLAIMS OR CORRESPONDENCE PERTAINING TO THIS PRODUCT.

IT IS EXTREMELY IMPORTANT THAT ALL CHARACTERS BE FURNISHED. THIS POINT CANNOT BE OVEREMPHASIZED. 000I-2 310G, 310SG AND 315SG BACKHOE LOADERS PC2755 (14-SEP-06) PN=2

Page 4

Contents

000I-3 310G, 310SG AND 315SG BACKHOE LOADERS PRODUCT IDENTIFICATION NUMBER TP16004 -UN-01JAN94 1. DESIGNATES BACKHOE MANUFACTURER T0 - JOHN DEERE DUBUQUE WORKS BE - BELL EQUIPMENT SOUTH AFRICA 2. DESIGNATES BACKHOE MODEL 315 3. DESIGNATES BACKHOE CONFIGURATION SG 4. DESIGNATES DUBUQUE WORKS SERIAL NUMBERS 893079 THRU 948698 DESIGNATES BELL EQUIPMENT SERIAL NUMBERS 200001 THRU XXXXXX 5. DESIGNATES UNIT TYPE BACKHOE LOADER 310G, 310SG AND 315SG BACKHOE LOADERS PC2755 (14-SEP-06) 000I-3 PN=3

Page 5