20 TESTING AND ADJUSTING Standard value table for engine . . . . . . . . . . . . . . . . . . . . . 20- 3 Standard value table for chassis . . . . . . . . . . . . . . . . . . . . 20- 4 Standard value table for electrical parts. . . . . . . . . . . . . . . . 20-8 Testing and adjusting parking brake linkage . . . . . . . . . . . 20-39 Service tools for testing, adjusting and Testing parking brake piston stroke . . . . . . . . . . . . . . . . . 20-40 troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . 20-10 Measuring engine speed . . . . . . . . . . . . . . . . . . . . . . . . . . 20-12 Measuring engine lubricating oil pressure . . . . . . . . . . . . .
20-13 Measuring fuel filter inlet restriction . . . . . . . . . . . . . . . . . 20-13 Measuring blow-by pressure . . . . . . . . . . . . . . . . . . . . . . 20-13 Measuring compression pressure . . . . . . . . . . . . . . . . . . 20-14 Measuring exhaust color . . . . . . . . . . . . . . . . . . . . . . . . . 20-15 Measuring coolant temperature . . . . . . . . . . . . . . . . . . . . 20-16 Measuring and adjusting valve clearance . . . . . . . . . . . . . 20-16 Measuring accelerator pedal . . . . . . . . . . . . . . . . . . . . . . 20-17 Measuring shift lever . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-19 Measuring stall speed . . . . . . . . . . . . . . . . . . . . . . . . . .
. . 20-20 Measuring torque converter, transmission oil pressure Checking for abnormality in . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-22 Method of operating emergency manual spool . . . . . . . . . 20-24 Testing and adjusting steering wheel . . . . . . . . . . . . . . . . 20-26 Measuring steering oil pressure . . . . . . . . . . . . . . . . . . . . 20-29 Measuring brake pedal . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-31 Testing and adjusting brake pedal linkage . . . . . . . . . . . . . 20-32 Measuring brake performance . . . . . . . . . . . . . . . . . . . . . 20-34 Measuring brake oil pressure . . . . . . . . . . . . . . .
. . . . . . . 20-35 Measuring wear of brake disc . . . . . . . . . . . . . . . . . . . . . 20-36 Bleeding air from brake system . . . . . . . . . . . . . . . . . . . . 20-37 Measuring parking brake performance . . . . . . . . . . . . . . . 20-38 Measuring wear of parking brake disc . . . . . . . . . . . . . . . 20-41 Measuring and adjusting work equipment control lever . . . . . . . . . . . . . . 20-42 Measuring stroke of work equipment valve spool . . . . . . . . . . . . . . 20-45 Measuring work equipment hydraulic pressure . . . . . . . . . . . . . . . . . . . . . . 20-46 Measuring work equipment . . . . . . . . . . . . . . . . . . . . . . . .
20-48 Testing and adjusting bucket positioner . . . . . . . . . . . . . . 20-50 Testing and adjusting boom kick-out . . . . . . . . . . . . . . . . . 20-51 Adjusting main monitor (Speedometer module) . . . . . . . . . . . . . . . . . . . 20-53 fuel level sensor . . . . . . . . . . . . . . . . . . . . . . . . 20-54 TROUBLESHOOTING TABLE OF CONTENTS . . . . . . . . 20-101 TROUBLESHOOTING SYSTEMS OF: ENGINE . S-MODE . . . . . . . . . . 20-143 HYD. AND MECHANICAL T-MODE . . . . . . 20-163 ELEC. FOR ENGINE, TRANS. E-MODE . . . . . . . . . . 20-185 MAIN MONITOR M-MODE . . . . . . 20-219 MAINTENANCE MONITOR K-MODE . . . . . . . . . . 20-247 EAGLE AIR CONDITIONER . . . . . . . . . . . . . . . . . .
. . 20-267 * See ENGINE SHOP MANUAL . i When using the standard value tables to make judgement for testing, adjusting, and troubleshooting, the following precautions are necessary: 1. The standard values in the tables are the values for a new machine and are given as reference values for the time when the machine is shipped from the factory. These values should be used as a guide when estimating wear after the machine is operated, and when carrying out repairs. 2.
The permissible values given in the tables are values estimated based on the results of various tests carried out on the machines shipped from the factory, so they should be used together with the information on the repair condition and other information such as the operating history of the machine when judging the condition of the machine. 3. These standard values do not form a basis for judging claims. When carrying out testing, adjusting, or troubleshooting, park the machine on level ground and use the safety pins and blocks to prevent the machine from moving When carrying out work together with co- workers, always use signals and do not let unauthorized people near the machine.
When checking the coolant level, always wait for the coolant to cool down. If the radiator cap is removed when the coolant is still hot, the coolant will spurt out and cause burns. Be careful not to get caught in the fan, fan belt or other rotating parts. 20-1 WA250-3L