Western Star 4700, 4800, 4900, 6900 — 35: Lighting Mods and Harness Repair

Western Star Bodybuilder Book: Revision 3.2a 1A Lighting Mods and Harness Repair P. 1A-35 b Guidline For Repairing or Replacing a Harness Turn Signal and Brake Override Circuit Elimination T.o.C. Repair Replace Western Star Trucks turn signal switches are equipped with a brake override circuit. Less than 20% of the harness is damaged. If the wire This circuit is designed to deactivate the 4-way flashers when the brakes are applied. In some vocations, customers prefer that the 4-way flashers remain flashing during damage is greater than 6 inches (15 cm), an overlay More than 20% of the harness use of the service brakes.

To disable this feature, the red jumper wire located in the harness can be added to replace the secƟon of damaged is damaged. turn signal switch housing, used to activate this circuit needs simply to be cut and wire. the ends taped or heat shrunk to remove this function. Both methods of wiring comply fully with Canada and USA regulations. Wire is smaller than 12-gauge. Wire is 12-gauge or larger. The harness is not readily available, or shipping will take The harness can be obtained in less Red Jumper longer than one week. than a week. Wire Wire insulaƟon is cracked due to excessive heat from an external source. Repair is recommended if the damage isisolated to one secƟon of the wire.

There is a clean cut to the wire, corrosion is wicked no Wire insulaƟon is cracked due to age, or more than 1 inch (2.5 cm) from the terminal end. If the damage is extensive and spread damaged area is over 6 inches (15 cm), the harness throughout the wire. can be repaired by adding overlay wiring over the damaged area. NOTE: If damage exceeds 1 inch (2.5 cm) from the terminal end, a quality repair may require adding a Installing Aftermarket LED Tail lights jumper wire to end, a quality repair may require adding a jumper wire to create enough slack in the wire.

If Adding LED Tail Lights requires the addition of a 2 W 560 OHM resistor adding extra splices stretches the wire too Ɵghtly it to ensure that the system consumes enough amperage for the system can degrade the integrity of the harness. to function properly. Use the splice instructions below for installation of the aftermarket resistor. Two harnesses are affected. For example, M2 24 pin The harness is proprietary, such as a Spl -1 lever lock connector (23-13144-010 and 23-13144-009) White - Amber LED Panel 2W 560 OHM RED LED Panel datalink with sheathing over a twisted is corroded on both sides.

Also, if the harness has Brown - RED LED Panel RED LED Panel pair, or a WABCO sensor and solenoid White - LED Side Marker Resistor RED Turn Signal Power minimal corrosion wicked up the wire, the connectors wiring. Green - Ground can be re-pinned Spl -2 If the damaged area is over 6 inches (15 cm), the Extensive damage to the harness caused Spl -3 harness can be repaired by adding overlay wiring by foreign material such as DEF fluid, Black - Amber LED Panel Black Park lite Power over the damaged area. diesel fuel, or road/deicer fluid.

Black - LED Side Marker Black - Red LED Panel For complete information see Guidelines for Repairing or Replacing an Electrical Harness - Service Bulletin 54-61in the Western Star Service Manual Models: 4700L/4800/4900/6900 Models: 4700L/4800/4900/6900 Guidline For Repairing or Replacing a Harness Repair Replace Less than 20% of the harness is damaged. If the wire damage is greater than 6 inches (15 cm), an overlay harness can be added to replace the secƟon of damaged wire. More than 20% of the harness is damaged. Wire is smaller than 12-gauge. Wire is 12-gauge or larger. The harness is not readily available, or shipping will take longer than one week.

The harness can be obtained in less than a week. Wire insulaƟon is cracked due to excessive heat from an external source. Repair is recommended if the damage isisolated to one secƟon of the wire. There is a clean cut to the wire, corrosion is wicked no more than 1 inch (2.5 cm) from the terminal end. If the damaged area is over 6 inches (15 cm), the harness can be repaired by adding overlay wiring over the damaged area. NOTE: If damage exceeds 1 inch (2.5 cm) from the terminal end, a quality repair may require adding a jumper wire to end, a quality repair may require adding a jumper wire to create enough slack in the wire.

If adding extra splices stretches the wire too Ɵghtly it can degrade the integrity of the harness. Wire insulaƟon is cracked due to age, or damage is extensive and spread throughout the wire. Two harnesses are affected. For example, M2 24 pin lever lock connector (23-13144-010 and 23-13144-009) is corroded on both sides. Also, if the harness has minimal corrosion wicked up the wire, the connectors can be re-pinned The harness is proprietary, such as a datalink with sheathing over a twisted pair, or a WABCO sensor and solenoid wiring. If the damaged area is over 6 inches (15 cm), the harness can be repaired by adding overlay wiring over the damaged area.

Extensive damage to the harness caused by foreign material such as DEF fluid, diesel fuel, or road/deicer fluid.