% O0001 (MX-EXAMPLE #1 – UPPER UNIT ONLY) (PREPARATION FOR START OF PROGRAM) (INITIALIZE - RAPID, ZX PLANE, TNR COMP CANCEL, TLO CANCEL, CYCLE CANCEL, UPR FEED) N1 G00 G18 G40 G49 G80 G99 N2 G00 G28 U0.0 V0.0 (ZERO RETURN X-AXIS & Y-AXIS) N3 G00 G28 W0.0 (ZERO RETURN Z-AXIS) N4 G00 G28 B0.0 (ZERO RETURN B-AXIS) N5 G490 S0 (EXPLICIT B-AXIS SPINDLE ORIENTATION FOR TOOL CHANGE) N6 G00 B-90.0 (EXPLICIT B-AXIS POSITIONING FOR TOOL CHANGE) N7 M01 (PREPARATION FOR START OF OPERATION) N8 G54 (WORK COORDINATE SELECTION) N9 M06 T01001 (SANDVIK C6-ASHR-38130-16-A - MCLNR-164D - CNMG432) N10 T02000 (STAGE NEXT TOOL) N11 G490 S0 (EXPLICIT B-AXIS SPINDLE ORIENTATION FOR TOOL) N12 G00 G28 W0.0 (ZERO RETURN Z-AXIS) N13 G00 G28 B0.0 (ZERO RETURN B-AXIS) N14 M138 (SHOWER BED COOLANT ON) N15 M126 (COOLANT THROUGH TOOL ON) N16 M34 (LEFT SPINDLE C-AXIS MODE OFF) N17 M261 (SPINDLE WINDING LOW - REPLACES M41) N18 G50 S2500 (MAXIMUM RPM CAP) N19 G96 S500 M03 P11 (CONSTANT CUTTING SPEED MODE - 500 FPM - LEFT SPINDLE CLOCKWISE) (FACE = ROUGH & FINISH) N20 G00 X3.7 Z0.01 N21 G01 X-0.0625 F0.018 N22 G00 Z0.11 N23 X3.7 N24 Z0.0 N25 G01 X-0.0625 F0.01 N26 G00 Z0.1 (OD CANNED ROUGH) N27 G00 X3.5 N28 G00 Z0.0615 N29 G71 U0.125 R0.03 N30 G71 P31 Q40 U0.02 W0.01 F0.018 N31 G00 X0.8903 N32 G01 X1.1817 Z-0.0842 N33 G03 X1.2 Z-0.1063 R0.0313 N34 G01 Z-1.125 N35 G01 X2.7875 N36 G03 X2.8317 Z-1.1342 R0.0313 N37 G01 X2.9817 Z-1.2092 N38 G03 X3.0 Z-1.2313 R0.0313 N39 G01 Z-2.225 N40 G01 X3.5 N41 G00 Z0.1 (TOOL CHANGE PREPARATION) N42 G00 G28 U0.0 V0.0 (ZERO RETURN X-AXIS & Y-AXIS) N43 G00 G28 W0.0 (ZERO RETURN Z-AXIS) N44 G00 G28 B0.0 (ZERO RETURN B-AXIS) N45 T01000 (CANCEL OFFSET FOR CURRENT TOOL) N46 M139 (SHOWER BED COOLANT OFF) N47 M127 (COOLANT THROUGH TOOL OFF) N48 M05 P11 (LEFT SPINDLE STOP) N49 G490 S0 (EXPLICIT B-AXIS SPINDLE ORIENTATION FOR TOOL CHANGE) N50 G00 B-90.0 (EXPLICIT B-AXIS POSITIONING FOR TOOL CHANGE) N51 M01 - 11 -