Komatsu — TORQUE LIST

. MAINTENANCE STANDARD TIGHTENING TORQUES FOR BOLTS AND NUTS STANDARD TIGHTENING TORQUES FOR BOLTS AND NUTS TORQUE LIST CAUTION Apply the following table for Hydraulic Hose. 4 - 14 If nuts, b olts, or ot her parts are not tightened to th e specified torque, i t wil l cause looseness or dam age to the tightened part s, and this will cause fail ure of the m achine o r problems with operation. Always p ay carefu l attention w hen tightening par Unless otherwis e specified , tighten the metr ic nuts and bolts to t he torque shown in th e table below. If it is ne cessary to replace any nut or bolt, always use a Komatsu genuine part of the sa me size as the part tha t was replaced.

Thread diameter of bolt (a)(mm) Width across flats (b)(mm) Tightening torque Target value Service limit Nm kgm lbft Nm kgm lbft 6 8 10 12 14 10 13 17 19 22 13.2 31 66 113 177 1.35 3.2 6.7 11.5 18 9.8 23.1 48.5 83.2 130.2 11.8-14.7 27-34 59-74 98-123 157-196 1.2-1.5 2.8-3.5 6.0-7.5 10.0-12.5 16.0-20.0 8.7-10.8 20.3-25.3 43.4-54.2 72.3-90.4 115.7-144.7 16 18 20 22 24 24 27 30 32 36 279 382 549 745 927 28.5 39 56 76 94.5 206.1 282.1 405.0 549.7 683.5 245-309 343-425 490-608 662-829 824-1030 25.0-31.5 35.0-43.5 50.0-62.0 67.5-84.5 84.0-105.0 180.8-227.8 253.2-314.6 361.7-448.4 488.2-611.2 607.6-759.5 27 30 33 36 39 41 46 50 55 60 1320 1720 2210 2750 3280 135.0 175.0 225.0 280.0 335.0 976.5 1265.8 1627.4 2025.2 2423.1 1180-1470 1520-1910 1960-2450 2450-3040 2890-3630 120.0-150.0 155.0-195.0 200.0-250.0 250.0-310.0 295.0-370.0 868.0-1085.0 1121.1-1410.4 1446.6-1808.3 1808.3-2242.2 2133.7-2676.2 Thread diameter a (mm) Width across flats b (mm) Tightening torque Target value Permissible range Nm kgm lbft Nm kgm lbft 10 14 14.7 1.5 10.8 12.7 - 16.7 1.3 - 1.7 9.4 - 12.3 14 19 29.4 3.0 21.7 27.5 - 39.2 2.8 - 4.0 20.3 - 28.9 18 24 78.5 8.0 57.9 58.8 - 98.1 6.0 - 10.0 43.4 - 72.3 22 27 117.7 12.0 86.6 88.3 - 137.3 9.0 - 14.0 65.1 - 101.3 24 32 147.1 15.0 108.5 117.7 - 176.5 12.0 - 18.0 86.8 - 130.2 30 36 215.7 22.0 159.1 176.5 - 245.2 18.0 - 25.0 130.2 - 180.8 33 41 255.0 26.0 188.1 215.7 - 284.4 22.0 - 29.0 159.1 - 209.8