Komatsu — Komatsu K EAM04 9 700 T Operation and Maintenance Manual for Bulldozers

STANDARD TIGHTENING TORQUES FOR BOLTS AND NUTS MAINTENANCE STANDARD TIGHTENING TORQUES FOR BOLTS AND NUTS 4 TORQUE LIST 4 If nuts, bolts, or other parts are not tightened to the specified torque, it will cause looseness or damage to the tightened parts, and this will cause failure of the machine or problems with operation. Always pay careful attention when tightening parts. Unless otherwise specified, tighten the metric nuts and bolts to the torque shown in the table below. If it is necessary to replace any nut or bolt, always use a Komatsu genuine part of the same size as the part that was replaced. Apply the following table for Hydraulic Hose.

4-14 CAUTION Thread diameter of bolt (a)(mm) Width across flats (b)(mm) Tightening torque Target value Service limit N·m kgf·m lbft N·m kgf·m lbft 6 8 10 12 14 10 13 17 19 22 13.2 31 66 113 172 1.35 3.2 6.7 11.5 17.5 9.8 23.1 48.5 83.2 126.6 11.8-14.7 27-34 59-74 98-123 153-190 1.2-1.5 2.8-3.5 6.0-7.5 10.0-12.5 15.5-19.5 8.7-10.8 20.3-25.3 43.4-54.2 72.3-90.4 112.1-141 16 18 20 22 24 24 27 30 32 36 260 360 510 688 883 26.5 37 52.3 70.3 90 191.7 267.6 378.3 508.5 651 235-285 320-400 455-565 610-765 785-980 23.5-29.5 33.0-41.0 46.5-58.0 62.5-78.0 80.0-100.0 170.0-213.4 238.7-296.6 336.3-419.5 452.1-564.2 578.6-723.3 27 30 33 36 39 41 46 50 55 60 1295 1720 2210 2750 3280 132.5 175.0 225.0 280.0 335.0 958.4 1265.8 1627.4 2025.2 2423.1 1150-1440 1520-1910 1960-2450 2450-3040 2890-3630 118.0-147.0 155.0-195.0 200.0-250.0 250.0-310.0 295.0-370.0 853.5-1063.3 1121.1-1410.4 1446.6-1808.3 1808.3-2242.2 2133.7-2676.2 Nominal - No.

of threads (a) Width across flats (b) (mm) Tightening torque Target value Permissible range N·m kgf·m lbft N·m kgf·m lbft 9/16 -18UNF 19 44 4.5 32.5 35 - 63 3.5 - 6.5 25.3 - 47.0 11/16 -16UN 22 74 7.5 54.2 54 - 93 5.5 - 9.5 39.8 - 68.7 13/16 -16UN 27 103 10.5 75.9 84 - 132 8.5 - 13.5 61.5 - 97.6 1 -14UNS 32 157 16.0 115.7 128 - 186 13.0 - 19.0 94.0 - 137.4 13/16 -12UN 36 216 22.0 159.1 177 - 245 18.0 - 25.0 130.2 - 180.8