. MAINTENANCE STANDARD TIGHTENING TORQUES FOR BOLTS AND NUTS STANDARD TIGHTENING TORQUES FOR BOLTS AND NUTS NOTICE When tightening panels or other parts having tightening fixtures made of plastic, be careful not to use excessive torque: doing so will damage the plastic parts. Pay enough attention when you tighten up. Apply the following table for Hydraulic Hose. 4 - 12 TORQUE LIST Unless otherwise specified, tighten the metric nuts and bolts to t he torque shown in t The tightening torque is determined by the width across the flats (b ) of the nut and b If it i s necessary to replace any nut o r bolt, always use a Komatsu genuine p art of the s ame size as the p art th at was replaced.
Thread diameter of bolt (mm) (a) Width across flats (mm) (b) Tightening torque [N·m (kgf·m)] Target value Permissible range 6 8 10 12 14 10 13 17 19 22 13.2 (1.35) 31 (3.2) 66 (6.7) 113 (11.5) 177 (18.0) 11.8 - 14.7 (1.2 - 1.5) 27 - 34 (2.8 - 3.5) 59 - 74 (6.0 - 7.5) 98 - 123 (10.0 - 12.5) 157 - 196 (16.0 - 20.0) 16 18 20 22 24 24 27 30 32 36 279 (28.5) 382 (39.0) 549 (56.0) 745 (76.0) 927 (94.5) 245 - 309 (25.0 - 31.5) 343 - 425 (35.0 - 43.5) 490 - 608 (50.0 - 62.0) 662 - 829 (67.5 - 84.5) 824 - 1030 (84.0 - 105.0) 27 30 33 36 39 41 46 50 55 60 1320 (135.0) 1720 (175.0) 2210 (225.0) 2750 (280.0) 3280 (335.0) 1180 - 1470 (120.0 - 150.0) 1520 - 1910 (155.0 - 195.0) 1960 - 2450 (200.0 - 250.0) 2450 - 3040 (250.0 - 310.0) 2890 - 3630 (295.0 - 370.0) Thread diameter a (mm) Width across flats b (mm) Tightening torque Target value Permissible range N·m kgf·m lbft N·m kgf·m lbft 10 14 14.7 1.5 10.8 12.7 - 16.7 1.3 - 1.7 9.4 - 12.3 14 19 29.4 3.0 21.7 27.5 - 39.2 2.8 - 4.0 20.3 - 28.9 18 24 78.5 8.0 57.9 58.8 - 98.1 6.0 - 10.0 43.4 - 72.3 22 27 117.7 12.0 86.6 88.3 - 137.3 9.0 - 14.0 65.1 - 101.3 24 32 147.1 15.0 108.5 117.7 - 176.5 12.0 - 18.0 86.8 - 130.2 30 36 215.7 22.0 159.1 176.5 - 245.2 18.0 - 25.0 130.2 - 180.8 33 41 255.0 26.0 188.1 215.7 - 284.4 22.0 - 29.0 159.1 - 209.8