SEN02094-00 40 Troubleshooting Failure code [DA2RMC] CAN communication error (work equipment and pump controller) 1 14 BR380JG-1E0 User code Failure code Trouble CAN communication error (work equipment and pump controller) (Work equipment and pump controller system) E0E DA2RMC Contents of trouble • Work equipment and pump controller detects communication error in CAN communication circuit between engine controller and machine monitor. Action of controller • Continues control based on the CAN communication information sent immediately before the trou- ble is detected. • Keeps the pump suction torque in a constant value (pump redundant level).
• If cause of failure disappears, system resets itself. Problem that appears on machine • Pump control becomes equal torque control. • Engine control is disabled (deceleration function etc.) • Machine information is not updated on the display. • Engine speed and coolant temperature cannot be detected. • Crusher clearance adjustment is disabled. • Horn sounds (three intermittent sounding) upon detecting a failure. Related information • Method of reproducing failure code: Turn the starting switch ON.
Possible causes and standard value in normal state Cause Standard value in normal state/Remarks on troubleshooting 1 Disconnection in wiring harness (Disconnec- tion or defective con- tact in connector) aPrepare with engine starting switch OFF, then carry out troubleshooting without turning engine starting switch ON. Wiring harness between C02 (female) (32) – P03 (female) (15), – P04 (female) (A), – G01 (female) (8), – CE02 (female) (46), – K02 (female) (A), – C05 (male) (3) Resistance Max. 1 z Wiring harness between C02 (female) (22) – P03 (female) (16), – P04 (female) (B), – G01 (female) (7), – CE02 (female) (47), – K02 (female) (B), – C05 (male) (10) Resistance Max.
1 z 2 Grounding fault in wir- ing harness (Contact with ground circuit) aPrepare with engine starting switch OFF, then carry out troubleshooting without turning engine starting switch. Between wiring harness C02 (female) (32) – P03 (female) (15), – P04 (female) (A), – G01 (female) (8), – CE02 (female) (46), – K02 (female) (A), – C05 (male) (3), and chassis ground Resistance Min. 1 Mz Between wiring harness C02 (female) (22) – P03 (female) (16), – P04 (female) (B), – G01 (female) (7), CE02 (female) (47), – K02 (female) (B), – C05 (male) (10), and chassis ground Resistance Min.
1 Mz 3 Hot short in wiring harness (Contact with 24 V circuit) aPrepare with engine starting switch OFF, then turn engine starting switch ON and carry out troubleshooting Between wiring harness C02 (female) (32) – P03 (female) (15), – P04 (female) (A), – G01 (female) (8), – CE02 (female) (46), – K02 (female) (A), – C05 (male) (3), and chassis ground Voltage Max. 5.5 V Between wiring harness C02 (female) (22) – P03 (female) (16), – P04 (female) (B), – G01 (female) (7), – CE02 (female) (47), – K02 (female) (B), – C05 (male) (10), and chassis ground Voltage Max.
5.5 V 4 Defective CAN termi- nal resistance (Internal short circuit or disconnection) aPrepare with engine starting switch OFF, then carry out troubleshooting without turning engine starting switch ON. K02 (male), P04 (male) Resistance Between (A) and (B) 120 ± 12 z 5 Defective work equip- ment and pump con- troller If causes 1 – 4 are not detected, work equipment and pump controller may be defective. (Since trouble is in system, troubleshooting cannot be car- ried out.)