Supermicro C7Z87-OCE — MNL-1507 - Z87 - Motherboard - Super Micro Computer, Inc.

Chapter 2: Installation 2-4 Installing DDR3 Memory Note : Check the Supermicro website for recommended memory mod­ ules. CAUTION Exercise extreme care when installing or removing DIMM modules to prevent any possible damage. DIMM Installation MH1 52 68 U103 51 MH2 HD AUDIO CLR_CMOS_SW C398 R743 THUNDERBOLT C401 J37 1. Insert the desired number of DIMMs into the memory slots, starting with P1-DIMMA2 (see the next page for the location). For the system to work properly, please use the memory modules of the same type and speed in the same motherboard.

J31 JI2C1/JI2C2 ON:ENABLE OFF:DISABLE 1 JL2 1 AUDIO FP PCIE3 PCIE5 PCIE1 PCH_SLOT1 PCI-E 2.0 X1 (INX4) JPCIE2 JPCIE6 JPCIE4 CPU_SLOT2 PCI-E 3.0 X4 (IN X16) PCH_SLOT3 PCI-E 2.0 X1 (INX4) 2-3:DISABLE 1-2:ENABLE JPAC1:AUDIO CPU_SLOT4 PCI-E 3.0 X8 (IN X16) JPAC1 JSPDIF_OUT 1 1 3 PCH_SLOT5 PCI-E 2.0 X1 (INX4) 18 34 CPU_SLOT6 PCI-E 3.0 X16 1-2 JPL2 DISABLE 2-3 ENABLE LAN2 1 1 FAN5 JPL2 4 JAUDIO1 USB 6/7(3.0) USB 16/17 USB 4/5(3.0) USB 14/15 JUSBLAN2 JUSBLAN1 LAN2 LAN1 JPW2 VGA/DVI JPUSB1 1 3 JHDMI JUSB01 MH3 HDMI USB 0/1 JI2C2 J1394_1 JCOM1 1 JI2C1 REV:1.00 1-2 JPL1 ENABLE 2-3 DESIGNED IN USA C7Z87-OCE DISABLE LAN1 JPL1 1 CPU J1 CPU 13 C A CATERR_LED 1 3 1 JVR1 59 1 4 FAN4 JTPM1:TPM/PORT80 COM1 JTPM1 1 5 LED2 10 6 LED3 10 6 2 2-3:NMI 1-2:RST WATCH DOG 2-3:ME RECOVERY 1-2:NORMAL JPME1:

JWD1: 1 JPEX_DEBUG 2 OC3_LED A C BIOS LICENSE R97 1 JITP1 CPU FAN1 4 1 JCHLED1 4 1 J38 1 3 JSTBY1 7 19 20 JWD1 1 2 1 1 3 1 1 JWOR1 JPME1 10 3 USB4/5 MH6 JWOR1: WAKE ON RING JBT1 + MH7 R298 2-3:ME MANUFACTURING MODE 1-2:NORMAL JPME2: FOR HOME OR OFFICE USE With FCC Standards Tested to Comply ALWAYS POPULATE BLUE SOCKET FIRST UNB NON-ECC DDR3 DIMM REQUIRED P1-DIMMA1 P1-DIMMA2 P1-DIMMB1 P1-DIMMB2 DIMM1 DIMM2 DIMM3 DIMM4 MH4 2. Push the release tabs outwards on JL1 C3491 J36 J35 J34 1 1 1 7 7 7 10 10 JL1: 2 2 USB8/9 USB10/11 OH/FF LED X CHASSIS INTRUSION USB6/7 MH5 2 1 7 1 3 8 7 2 1 JPUSB2 A-SATA0 I-SATA0 I-SATA1 I-SATA2 T-SGPIO2 JSD1:

SATA DOM PWR 3 JSD1 1 1 1 19 JUSB30_I1 JF1 USB 2/3(3.0) USB 2/3 U197 U196 2-3:BIOS RECOVERY 1-2:NORMAL JBR1: 10 11 1 1 16 JLED1 1 JPME2 JBR1 C 1 JUSB30_I 19 A LED1 1 1 USB 0/1(3.0) USB12/13 FAN3 4 JD1 4 RT1 MH8 R154 C582 C591 R155 11 C592 NIC1 SPEAKER:1-4 JD1: BUZZER:3-4 R156 10 JLED1: 3 PIN POWER LED 1 JPW1 24 13 SP1 + + RST PWR JF1 ON NIC2 HDD PWR LED LED 1 6 JOCE 3 1 JVR2 4 1 FAN2 MH9 both ends of the DIMM slot to unlock it. 3. Align the key of the DIMM mod­ ule with the receptive point on the memory slot. 4. Align the notches on both ends of the module against the receptive points on the ends of the slot. Notches 5.

Use two thumbs together to press the notches on both ends of the module straight down into the slot until the module snaps into place. 6. Press the release tabs to the lock Release Tabs positions to secure the DIMM module into the slot. Press both notches straight down into the memory slot. Removing Memory Modules Reverse the steps above to remove the DIMM modules from the motherboard. 2-11