The following example shows the output for the show l2vpn evpn mac evi evpn-instance command on VTEP 2: Leaf-02# show l2vpn evpn mac evi 101 MAC Address EVI VLAN ESI Ether Tag Next Hop(s) -------------- ----- ----- ------------------------ ---------- --------------- 44d3.ca28.6cc1 101 101 0000.0000.0000.0000.0000 0 172.16.254.3 44d3.ca28.6cc2 101 101 0000.0000.0000.0000.0000 0 Gi1/0/10:101 Leaf-02# The following example shows the output for the show ip mroute command on VTEP 2: Leaf-02# show ip mroute IP Multicast Routing Table Flags:
D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, E - Extranet, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group, G - Received BGP C-Mroute, g - Sent BGP C-Mroute, N - Received BGP Shared-Tree Prune, n - BGP C-Mroute suppressed, Q - Received BGP S-A Route, q - Sent BGP S-A Route, V - RD & Vector, v - Vector, p - PIM Joins on route, x - VxLAN group, c - PFP-SA cache created entry, * - determined by Assert, # - iif-starg configured on rpf intf, e - encap-helper tunnel flag Outgoing interface flags:
H - Hardware switched, A - Assert winner, p - PIM Join Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.0.1.40), 00:05:51/00:02:24, RP 172.16.255.255, flags: SJCL Incoming interface: GigabitEthernet1/0/2, RPF nbr 172.16.24.2 Outgoing interface list: Loopback1, Forward/Sparse, 00:05:49/00:02:09 GigabitEthernet1/0/1, Forward/Sparse, 00:05:43/00:02:24 (*, 225.0.0.101), 00:02:46/stopped, RP 172.16.255.255, flags: SJCFx Incoming interface: GigabitEthernet1/0/2, RPF nbr 172.16.24.2 Outgoing interface list: Tunnel0, Forward/Sparse-Dense, 00:02:46/00:00:15 (172.16.254.4, 225.0.0.101), 00:01:43/00:01:16, flags: FTx Incoming interface:
Loopback1, RPF nbr 0.0.0.0 Outgoing interface list: GigabitEthernet1/0/2, Forward/Sparse, 00:01:43/00:02:45 (172.16.254.3, 225.0.0.101), 00:02:19/00:00:40, flags: JTx Incoming interface: GigabitEthernet1/0/2, RPF nbr 172.16.24.2 Outgoing interface list: Tunnel0, Forward/Sparse-Dense, 00:02:19/00:00:40 Leaf-02# The following example shows the output for the show ip mfib command on VTEP 2: Leaf-02# show ip mfib Entry Flags: C - Directly Connected, S - Signal, IA - Inherit A flag, ET - Data Rate Exceeds Threshold, K - Keepalive DDE - Data Driven Event, HW - Hardware Installed Configuring EVPN VXLAN Layer 2 Overlay Network Example:
Configuring Layer 2 VNI with Spine Multicast Replication Configuring EVPN VXLAN Layer 2 Overlay Network 39