cisco — Example: Configuring Layer 2 VNI with Spine Ingress Replication

Verifying the Layer 2 VNI with Spine Ingress Replication The following sections provide sample outputs for show commands to verify the Layer 2 VNI with spine ingress replication on the devices in the topology configured above: Outputs to Verify the Configuration on VTEP 1, on page 51 Outputs to Verify the Configuration on VTEP 2, on page 53 Outputs to Verify the Configuration on Spine Switch 1, on page 56 Outputs to Verify the Configuration on Spine Switch 2, on page 58 Outputs to Verify the Configuration on VTEP 1 The following example shows the output for the show nve peers command on VTEP 1:

Leaf-01# show nve peers Interface VNI Type Peer-IP RMAC/Num_RTs eVNI state flags UP time nve1 10101 L2CP 172.16.254.4 3 10101 UP N/A 01:25:20 Leaf-01# The following example shows the output for the show ip route command on VTEP 1: Leaf-01# show ip route Codes:

L - local, C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, m - OMP n - NAT, Ni - NAT inside, No - NAT outside, Nd - NAT DIA i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route H - NHRP, G - NHRP registered, g - NHRP registration summary o - ODR, P - periodic downloaded static route, l - LISP a - application route + - replicated route, % - next hop override, p - overrides from PfR & - replicated local route overrides by connected Gateway of last resort is not set 172.16.0.0/16 is variably subnetted, 12 subnets, 2 masks C 172.16.13.0/24 is directly connected, GigabitEthernet1/0/1 L 172.16.13.3/32 is directly connected, GigabitEthernet1/0/1 O 172.16.14.0/24 [110/2] via 172.16.13.1, 01:26:20, GigabitEthernet1/0/1 C 172.16.23.0/24 is directly connected, GigabitEthernet1/0/2 L 172.16.23.3/32 is directly connected, GigabitEthernet1/0/2 O 172.16.24.0/24 [110/2] via 172.16.23.2, 01:26:20, GigabitEthernet1/0/2 C 172.16.254.3/32 is directly connected, Loopback1 O 172.16.254.4/32 [110/3] via 172.16.23.2, 01:26:20, GigabitEthernet1/0/2 [110/3] via 172.16.13.1, 01:26:20, GigabitEthernet1/0/1 O 172.16.255.1/32 [110/2] via 172.16.13.1, 01:26:20, GigabitEthernet1/0/1 O 172.16.255.2/32 [110/2] via 172.16.23.2, 01:26:20, GigabitEthernet1/0/2 C 172.16.255.3/32 is directly connected, Loopback0 O 172.16.255.4/32 [110/3] via 172.16.23.2, 01:26:20, GigabitEthernet1/0/2 Configuring EVPN VXLAN Layer 2 Overlay Network Example:

Configuring Layer 2 VNI with Spine Ingress Replication Configuring EVPN VXLAN Layer 2 Overlay Network 51