US Army Materiel Command AMCP 706-250 — Engineering Design Handbook: Guns Series — Guns-General

Downloaded from https://www.everyspec.com (a) Arrangement and Functioning Power for all mechanical operations is provided by an electric motor, through a transmission case, both mounted above the gun, forward of the breech, on the nonrecoiling recoil cradle. A housing sup- porting the ammunition-contacting parts of the fuze setter and rammer, final drive gears and shafts, opening and closing devices, operating control rods, and a feeding trough is attached to and partially encloses the breech ring.

A drive shaft and control rod for each unit (setting and ramming) extend for- ward to appropriate connections with the transmis- sion case, the connections being arranged to disen- gage as the gun recoils and re-engage at completion of counterrecoil. The feeding trough is a'igned with the gun bore, sufficiently behind the breech ring to accommodate the fuze setting and ramming opera- tions in the intervening space. The ramming is accomplished by gear-rotated hourglass-shaped rub- ber rolls, mounted on pivoted arms, on opposite sides of the gun line of bore, immediately forward of the trough.

A spring-cushioned plunger linked to the supporting arms governs lateral distance between the rolls, release of the plunger on gun recoil increasing the separation, and depression of the plunger, on the gun's return to battery, nar- rowing the space to cartridge-gripping distance. The increase of separation provides clearance for fired case ejection. Two automatically shifted speeds of roll rotation are provided: slow for feed- ing the cartridge into the fuze setter and fast for subsequently propelling it into the chamber.

The fuze setter presents, forward of the ramming rolls, a gear-driven ring with internal retractable jaws to seat the nose of the round and rotate the time- fuze ring to the desired setting. The fuze setter and ramming roll drive shafts are connected by a differential mechanism in the transmission case, and the amount of rotation permitted the fuze setter is governed by a data receiver on the side of the case. This unit operates through suitable link- age to disengage a clutch on the fuze-driving trans- mission shaft when the fuze has been set. Retrac- tion of the fuze setter jaws then provides clearance for the cartridge to pass through the ring into the gun bore.

-Retraction and closing of the jaws is effected by a rack shaft (control rod) actuated from the fuze setter shaft in the transmission case. The jaws remain retracted (open) from completion of fuze setting until the gun returns to battery after recoil. (b) Sequence of Operations Starting with the gun breech open and the fuze setter-rammer motor running, the procedure is as follows: (1) The round is placed manually nose for- ward on the loading trough and pushed gently forward into the slowly rotating rammer rolls. (2) The ramming rolls move the round for- ward to seat the nose firmly in the fuze setter jaws. When the round is seated the rolls are stalled.

(3) Stalling of the rammer rolls actuates op- eration of the differential in the transmission to produce rotation of the fuze setter drive shaft and set the fuze. (4) Completion of the fuze setting actuates the fuze jaw retracting rod to open the fuze setting jaws and shifts the rammer rolls into high speed. (5) The rapidly driven rolls impel the round into the chamber, tripping the extractors, and the breech closes. (6) The firing control is actuated by hand. (7) The gun recoils and the ramming rolls open. (8) The gun returns to battery, opening the breech, ejecting the fired case and cocking the firing mechanism.

The final action actuates shift of the rammer rolls to feeding position and slow speed, and the closing of the fuze setter jaws. The gun is then ready for the next round. 3-8.1.2.5 Magazine Type Loader-Rammer This type (Figure 3-22) of powered feeding de- vice has been developed for vertically sliding breechblock cannon using fixed ammunition. It transfers the round from a previously loaded maga- zine, rams it into the chamber, and actuates the firing mechanism, requiring only that the operating control be retained in the firing position.

A typical design combines a scroll-shaped magazine above and rearward of the gun breech, feeding rounds sideward from either right or left to the center; a centrally located rammer tray, crank supported, that receives each successive round from the maga- zine, lowers it to alignment with the gun bore, and impels it into the gun by means of an endless chain rammer; and a cased motor driven transmission unit centrally mounted above the gun, forward of 3—21