Downloaded from https://www.everyspec.com charges also, as may be necessary for satisfactory ignition. respondingly, with resulting variation in the shape of the representative pressure-travel curve and in the muzzle velocity of the projectile. (b) Separately bagged (or wrapped) basic charge and increments are also utilized as com- ponents of semifixed ammunition for zone firing of muzzle-loading mortars. In this use the sepa- rate portions of the complete charge are attached to the fins or fin shaft of the projectile, with the in- crements readily removable in the field to reduce the range from the maximum to the zone desired.
A primer cartridge is carried in the rear of the fin shaft of the projectile. 5-5.3 Pressure Waves If an insufficient fraction of the propellant is ignited initially, the difference in progress of com- bustion in various parts of the chamber tends to produce severe surging of the produced gases ai*d irregular rise of pressure. The resulting pressure waves may cause unpredictable variations in the height and location of the peak of the pressure- travel curve, with resultant variations in muzzle velocity. There is also the possibility that the pres- sure peak may occur at such location as to subject a portion of the tube to pressure higher than is permissible at that section.
(3) Grain arrangement. Generally, whether cased or bagged, propellant charges composed of the commonly used shapes of grain are assembled with the grains in random positions. However, where large rod-shaped grains are used in a package of large length-to-diameter ratio, improvement in compactness, rigidity and uniformity may be ob- tained by orderly arrangement of grains, end to end, with axes parallel to the axis of the container. A charge thus arranged is termed a stacked charge The primer, alone or supplemented by one or more ignition charges, is the means by which the burning of the propelling charge is initiated.
The primer contains an explosive mixture designed to be highly sensitive to impact, friction, or other shock, mechanical or electrical, in accordance with the means of firing provided by the gun. On acti- vation by the firing mechanism, the primer projects a quick, hot flame against the propellant (or a supplementary igniter charge) contained in the more forward portion of the case.
For the rela- tively small quantities of propellant contained in small arms cartridges, the primer ignites the pro- pellant directly; for the larger quantities of propel- lant (and, generally, slower burning granulations) contained in cased artillery ammunition, the primer ignites a quantity of quick-burning black powder (igniter) so placed as to distribute an igniting flame to all portions of the propellant in the least possible interval of time. Elements of the igniter charge may extend to the forward end of the pro- pellant charge.
For large caliber guns using bagged propellant (without cartridge case) a rela- tively small primer is used, to project a jet of flame through a passage bored on the axis of the breech- block into the gun chamber, to ignite additional igniter units accompanying the propellant. The additional igniter charges are generally contained in, or attached to, each bag or increment of pro- pellant, to further the rapid propagation of the igniting flame.
5-5.4 Primers and Igniters 5-5 Ignition Systems 5-5.1 General The release of the propellant's high energy in a very short time interval, with the necessary round- to-round uniformity, requires that the propellant be ignited by the quickest possible propagation of high-temperature gas to the largest possible frac- tion of the total surface of the propellant, with the least round-to-round variation that can be practi- cally attained. (The ideal performance would be instantaneous ignition of the total surface of the propellant.) The effectiveness of the means of ignition, therefore, constitutes an important factor in the effectiveness of propellant performance.
Some effects of inadequate ignition are indicated briefly below. 5-5.2 Relation Between Ignition and Muzzle Velocity The uniformity of the projectile muzzle velocity effected by the propellant may be represented by uniformity of the area under the pressure-travel curve (Figure 5-1). If the elapsed time between the beginning and completion of ignition of all sur- faces of the propellant varies from round to round, the early rate of burning and the total time to complete burning of the propellant will vary cor-