— AMCP 706-286 — Engineering Design Handbook (1963)

Downloaded from https://www.everyspec.com DESIGN CONSIDERATIONS cient will the design be from the structural missiles until such time as separate design standpoint. criteria are established for missiles or if the 4-4.1. Ty-pes of Loads. Stress analysts fre- procuring agency dos not specify safety fLc- quent1 spaes of primrk s. nd second ofc toiz in a specific missile development. ]a,- loads. Primary loads are the maj,,r loads tors cf safr t y are applied to limit loads to that must be resisted and transmitted b, tntL take into a ccount neertainties in coniectior. sructure. Consider, for example, that under with the establishment tif the limit !oadi., - - are acting on the missile structure.

If we cut stress analyss. off tne tail portion and examine the equi- librium of this portion as a free rigid body, tural DeinAsue tha tydiner s then three forces and three moments will be ural Design. Assume thathe designer has required at the section of the cut in order o tentatively chosen a thin-walled circular .yl- maintain equilibrium. These may be consid- inder as a structural configuration; this ered as the primary loads being transmitted choice based upon his experience and infor- Sat the section, mation available on the expected environment and mission of the vehicle. It may be con- Secondary loads are self-equilibrating.

venient to consider that aside from the nose They are a consequence of structural defer- cone and control vanes, the circular cylinder , mations rafnez than externally applied loads. Thma ratheere an exnalpled seoad-, comprises the entire body of the -missile. One Thrml stresses Areanhexampuh second - can now confine himself to the applied loads, ary stresses. Although secondary stre ens and inquire into the efficiency of the struc- Scan be disregarded in some branches of en- tural configuration, and into the effect that gineering, they cannot be overlooked in mis- the magnitude of the loads and design cri- sile structural design. teria have on material selection and required F.

) The principal loads on the missile struc- on areas. ture areaerodynamic, inertial, and thermal. c igure 4-3 i a photograph of he tni sec- a particular flight wzondition, certain loads properties of materials, and a.lithods of Therearealso important loads which are im- tion of the Jupiter missile illustr.tive of posed on the structure that do not fall pre- - the thi-walled circular cylinder as a _-ruc- cisely in the above categories, but which are tural configuraion. Note the extremely large tnevertheless important in determining the ratio of radius to wall thickness and the cir- structural design.

These include loads in- cumferential reinforcement rings, The photo- duced by the propulsive system, those induced graphi re 44so s The pto by internal pressurization, fuel slosh, vibra- g ,ph in Figure 4-4 shows the top section of boy intern lo essurizatontfue s , vira- the Redstone being inspected prior to move- tory loads, and loads encountered in trans- ment to the assembly area where internal portation, handling and launching. equipment is installed. In the background is 4-4.2 Limit and Ultimate Loads; Factor the nose cone in which the warhead is in- of Safety. The loads that are actually antici- stalled.

pated during the lifetime of a missile are Treating the circular cylinder as a beam, called limit load8. These loads may be cal- the cylinder is required to transmit three culated by specialists in various fields and f'-irce and three moment components at any the information made available to the struc- cross-section. For simplicity, the two force tural analyst and designer. It is possible that components in the plane of the cross-section data in the form of tables and curves can be can be obtained Into a single shear force, and made available to the designer for prelimi- the two moment components in the plane of nary design purposes.

Limit loads are multi- the cross-section into a single bending mo- plied by a factor of s8fety to 'jbtain ultimate ment. The remaining foree component is an loads. In the design of aircraft, factors of oxial force, the rtmaining moment compcn- safety are specified; these can be applied to ent is called the tor 1 e. 6 63