US Army Materiel Command AMCP 706-341 — Engineering Design Handbook — Carriages and Mounts Series: Cradles

Downloaded from https://www.everyspec.com is attached to the cradle and the movable por- D. EqUILIBRATOR ) tions are attached to the recoiling parts. There 7. One end of the equilibrator is attached are, in general, two basic arrangements for the to the top carriage and the other to the cradle. recoil mechanism. One has the recoil cylinder A large turning radius about the trunnion is and recuperator fixed to the cradle and the desirable for the equilibrator as -t lowers the piston rod fixed to the gun lug or breechblock. forces. Hence, a more efficient design results.

The other arrangement fixes the recoil cylinder The attachment on the cradle may be at any and recuperator to the gun and the rod to the convenient location on the structure or on the cradle. In the former case, the cylinder and elevating arc, provided that clearances and recuperator are either integral parts of the strength requirements are met. Equilibrator cradle or separate parts rigidly attached to it. design is discussed in Ordnance Corps Pamph- It is well to have the recoil mechanism in.

let ORDP 20.345.* stalled as near as possible to the tube, not only for compactness but also for lower bending moments on the cradle which are axiomatic to lower stresses and, therefore, lighter stiucture. III. TYPES OF CRADLE B. TRUNNIONS 8. There are two basic types of cradle, 5. The trunnions are considered to be com- designated according to the general form of ponents of the cradlju whether te trunnion cross section as the U-type and the O-type. bearings are located on the side frames or in Each has its own method of seating the gun the cradle itself. The trunnions, through tube. The U-type seats the tube on top and which the firing loads are transmitted, are the retains it by guides.

The 0-type holds the main att-chment to the top carriage and also tube in a hollow cylinder whose inner wall con- serve ae le pivot about which the tipping forms to the mating portion of the tube. parts rotate during elevation. In the plan(_ view, their axis should lie normal to the A. THE U-TYPE CRADLE direction. of recoil. In the side view, the 9. The degree of resembiance between the trunnion axis should be located on or near the U-type cradle and the letter U depends on line parallel to the bore and. passing through constructional features. If the recoil cylinder the center of gravity of the recoiling parts.

and recuperator are attached to the gun tube This reduces tipping moments during firing so that they become part of the recoiling and relioves the elevating arc of large loads, system (Figure 2), the cradle may be ap- proximately U-shaped, with provisions for ac- C, ELEVATING MECHANISM commodating rails and trunnions. If the re- 6. The elevating mechanism terminates st coil cylinder and recuperator are integral with the elevating are which is a gear segnmat the cradle (Figure 3), the resemblance to a U- rigidly attached to the cradle. It is here that section is lost.

However, the term, U-type, the torque required to elevate is applied to the still applies to indicate the general construc- tipping parts. The pitch radius of the ele- tion. For simplicity, the recuperators are vating arc is centered at the trunnions and omitted from Figures 2 and 3. should be as large as possible and still remain 10. If the recoil cylinder and recuperator compatible with the size of the rest of the are attached to and recoil with the gun tube, structure. A large radius results in small gear the structure which supports them is called a tooth loads and less effort to elevate the gun. sleigh.

The sleigh carries the rails and thus Also, if the arc is large, the attachments to the supports the tube in the cradle. It may be a cradle can be located farther apart and, al- forging or a weldment. If a forging, the though the torque transmitted to the tipping cylinders of the recoil mechanism are bored parts remains unaffected, the corresponding directly into it. loads at the attachment points are decreased. * Reference 3.