US Army Materiel Command AMCP 706-341 — Engineering Design Handbook — Carriages and Mounts Series: Cradles

Downloaded from https://www.everyspec.com A will peak excessively because of the deflections. slides in the keyways of each bearing. Al- A means of circumventing peak pressures em- though the rifling torque is applied for only a ploys the practice of providing enough flexi- short recoil distance, the key should be long biiity in the structure to enable the deflection enough to maintain contact with the bearings of one mating surface to conform to the deflec- at all positions of the recoil stroke so that no tion of the other, thus maintaining the original difficulty in alignment develops during coun- contact area. But this type of structure is not teriecoil.

always feasible and may not be applicable to cradle design. If not, one must resort to ap- proximation methods that are available for D. EFFECT OF FRICTION ON SLIDING SURFACES determining the required bearing area. One such method assumes a uniform load distribu- 36. Frictional forces, as such, are not a tion with the maximum design pressure limited srucusregt in oth spects, the to 50 pi (se Pragrph 8).structural strength. In other aspects, they to 500 psi (see Paragraph 28. present serious problems. For design analysis, the present practice is to use a coefficient of C. SLIDING SURFACE OF O-TYPE CRADLE friction of 0.15*. Friction resists recoil and thus forms part of the recoil force.

Theoret- 34. The general discussions on the sliding ically, it does not matter whether the recoil surfaces of the U-type cradle apply as well to force is generated by friction or by the recoil those of the 0-type cradle. It is advan- mechanism. However, it is desirable to keep tageous to have the center of gravity of the friction to a minimum by proper lubrication recoiling parts located as near as possible to because wear and eventual damage to the the bearings. For the load analysis, the bear- sliding surfaces are less likely to occur. Also, ings are usually far enough apart to assume a frictional forces are somewhat of an unknown uniform load distribution.

The tipping mo- value on exposed surfaces and may vary con- ment during recoil produces the largest loads siderably. If their maximum value is small, on the bearings. A bearing pressure of 200 to it will constitute only a small part of the total 300 lb/in is desirable but pressure should not exced 50 l/in (se Paagrph 8).The recoil force and will have only a slight effect on exceed 500 lb/in 2 (see Paragraph 28). The the functioning of the recoil mechanism. O-type differs in that the gun tube is keyed to the cradle and in that the reaction to the rifling torque is transmitted by the key, not by E. EFFECT OF TEMPERATURE VARIATION ON the sliding surfaces (see Figure 11).

Because SLIDING SURFACES the structure must be held to reasonable pro- portions, and the sliding surface offered by the 37. Artillery is (mployed in both desert and key is limited in area, the bearing pressures arctic climates. Changes in the ambient here may be much higher than on other sliding temperature will shrink or expand the struc- surfaces. However, due to the extremely short ture. If made of like material, all components duration of the rifling torque, allowable bear- will be affected equally, causing no relative ing pressures may be high. After incorporating displacement among them.

However, if the Sthe fator of safety, they nmy approach the structural members are of unlike material, bearing strength of the material, their rates of expansion will differ and this may 35. The construction of the sliding surfaces prove dileterious sinply by reducing clear- of the O-type cradle is relatively simple. The ances between moving parts to the extent primary structure is a cylinder in which the where binding impends. The sliding surfaces gun tube slides during recoil.

A bronze bearing of cradles must be of different materials be- at each end and a straight portion of the gun cause two mating surfaces of like material tube, machined to a 32 rms finish, provide the seldom provide compatible sliding properties. sliding surfaces. Thus, the gun tube serves as Bronze makes an excellent sliding surface for its own slide and the bearings serve as guides. steel. Its coefficient of linear expansion is The key is usually secured to the gun tube and * Reference 4. 15