Downloaded from https://www.everyspec.com AMOP 706-117 while others were exposed to unfiltered air for a period vegetation. Therefore, the probability of military equip- of 56 days; those exposed to unfiltered air suffered a 10 ment being exposed to high levels of hydrogen fluoride percent greater loss in breaking strength than the unex- is very low. posed.
2-7.4.8 Dyes 2-7.5 ELECTRONIC SYSTEMS AND COMPONENT DAMAGE An exposure study involving 69 dye-fabric combina- tions indicated a high susceptibility of nearly one- A survey of manufacturers of electronic components fourth of the combinations to fading when exposed to indicated that airborne particulates are considered re- urban environments (Ref. 48). Fading is much greater sponsible for most of the damage to components rather at urban sites than at corresponding rural control sites than sulfur dioxide as had been previously indicated for these dye-fabric combinations showing a high de- (Ref. 49). Particulates cause damage to electronic corn- gree of fading.
Controlled exposures to irradiated or ponents in five different ways, i.e., nonirradiated automobile exhaust show that photo- (I) Interference with the important photoengraving chemically produced components of the atmosphere techniques used in fabrication of many compiients cause the fading. Also, the study revealed synergistic (2) Spot formation on the screens of TV and cath- effects of pollutants in combination.
The addition of ode ray tubes sulfur dioxide to the irradiated automobile exhaust (3) Contamination of vacuums by releasing ab- emissions produced more than an additive effect on the sorbed gases fabrics, when compared to the effects of sulfur dioxide in clean air or in irradiated auto exhaust without added' (4) Creation of microscopic surface leakage paths sulfur dioxide, in semiconductors and integrated circuits Certain dyed cellulosic fabrics show fading when (5) Creation of gross current leakage paths in all exposed to nitrogen oxides at relative humidities electronic equipment. greater than about 50 percent.
Fading occurs in certain The effects of air pollutants on computers are sum- blue and green shades, representing dyes from four marized as follows: "silver contacts in relays build up major classes-direct, sulfur, vat, and reactives a high resistance surface, copper wiring connectors dyes-when exposed to different field environments in become unreliable, gasket seals deteriorate, protective the absence of light (Ref. 8). finishes become tacky or erode away, bearing life is shortened, reaction products plug small orifices and 2-7.4.9 Glass and Ceramics interfere with precision adjustments, and in general adversely affect the operating life of a computer" (Ref.
Glass and ceramics show very good resistance to 50), atmospheric pollutants. One major item of interest, however, is the effect of atmospheric pollutants on elec- trical insulators. Although air pollutants do not in 2-7.6 CASE HISTORIES9 themselves damage the insulator, particulate matter deposited on the surface of insulators used on high- Very few case histories of tIr pollutant damage have voltage power lines will, in the presence of moisture, damage eaused by asir pollutants. For example, how form conducting paths resulting in leakage currents, d flashover, or puncture of the insulator.
For a more much paint degradation can be attributed to pollutants detailed discussion of these effects see Chap. 3. par.. as compared to the natural environmental factors? What Scauses an electrical switch to fall? Among the domage 3-5.4, "Electrical Contacts and Connectors", and espe- cauen tracal switch to all Aonte amage cially Fig. 3-23 that compares 60-Hz flashover voltages incidents that have been traced to air pollutantw. the for clean and dry, clean and wet, ancs dirty and wet prime cauatlve factor aid the following: insulators. (1) Navigation aids facinity-FAA.
A very high ore- It is well known that hydrogen fluoride (HF) will quency omnidirectional ranging (VOR) station oper- etch glass. The concentrations required to produce viai- ated by the Federal Aviation Administration (FAA) ble damage to glnet and other materials are believed to near Charleston, W Va., started experiencing problems be far in excess of those required to kill many types of about one year after the equipment was installed. The kmajor problem was sulfiding of silver-plated contacts resulting in arcing and pitting to the extent that re- 9. A general reference for this paragraph is Ref. 49. placements were required. 2.64