Namco · Dunkmania · 4 pp.
Namco Dunkmania Операционный Руководство: Полный Пользовательский и Сервисный Руководство PDF
Related manuals
Document text
Nance DUNKMANIA OPERATION MANUAL A\ CAUTION In order to safely use this machine, be sur e to car efull y r ead this oper ation manual and the manual installation and oper ation. DISTRIBUTED BY: of the cabinet in which this machine to be installed befor e NAMCO LIMITED 2-8-5 TAMAGAWA, OHTA-KU, TOKYO, 146, JAPAN ©1995 NAMCOLTD., ALL RIGHTS RESERVED
1. Cautions (1) Be sure to turn off the cabinet whenever installing or removing the PC board. Otherwise you may be hurt by an electric shock. (2) Be sure to use an edge connector which is applied to the JAMMA standard. Any modifications such as cutting the edges of PC boards will cause a failure and also will be out of our guarantee for repair. (3) Never test the PC boards for conductivity with a multimeter or similar device. The PCB contains sensitive chips which could be destroyed even by the internal voltage of such a device. (4) Foreign matters or dust on the PC boards will cause a failure. Tum off the power and clean the PC boards with a brush or similar thing.
(5) When transporting the PC boards, wrap them with sponges or air caps and pack them in a card board box so that they can avoid a direct impact from outside during shipment. (6) For maintenance, 2. contact your distributor. Specifications LP, Start One-side 4-P specifications (1) Control panel: 8-direction lever: 4(1P, 2P, 3P,4P, 1 each) 12( 1P, 2P, 3P,4P, 3 each) - Button switch: Button 1 : (Shift) Button 2 : (Shot& Block) 3 : (Passé& Steal) Button 4(1P, 2P, 3P,4P, * Start switch: @ ; v Oo x . (3) Direction of monitor: @ DOD Lo 1P,B Horizontal * 3P. 8-direction | 4P. 8-direction /.
“coy v @ “Oo KAY X 2P, Buon 1\ 2 \ 2P, Button 3 4P, Start 2P, Button an 3P, ~~ Kh 4 But on ‘ea 4P, Button\\ 2 3 = Fig. 1 SODO A 2p,3P,Baton Button \ 2 3 © @ BODOEDOS NA 230 x 230mm — 2 LP,Button Button1] 2 ; 3P, Start 2P, 8-direction Y 1P, 8-direction 1 each) (2) PC board size: : 2P, Start eee 3.Connection (1) Connection of control panel See above to connect JAMMA (see P3 : PC harness and extended harness(accessory) to control panel through the cabinet board connector table) Connecting expanded harness to the right speaker allows you to enjoy a stereophonic effect. (2) Connection of PC board Set the PC board in the cabinet and connect JAMMA (DDK 225D-10024C2-2312) to the PC board.
edge connector and 48P extended edge connector 48Pextendededge 4. Explanation of PC connector Boards 12 (1) Option switches No.1 to "ON" for Test Mode. No.2 to "ON" for Screen Freeze. Normally, all of the option switches are "OFF". 56P edge connector (JAMMA) O Speaker volume \ Option switch (2) Speaker volumes To decrease the sound volume of the speaker, turn the speaker volume counterclockwise. Fig. 2 5. Test Mode (1) The PC Board enters the test mode by setting the test switch on the PC Board to "ON" on the game screen. And the test menu screen is displayed on the monitor. Use the test switch (For connection, see P3:
PC Board Connector Table) on the cabinet or the option switch on the PC Board (see PI: 4.(1) Option switches) When an item is selected by operating the 1P control lever up and down and the {P button! switch is pushed, the selected test screen is displayed. (2) Game fees can be changed on the coin option screen, and the game difficulty can be changed on the game option screen. Select an item by operating the 1P control lever up and down, and change its contents using the IP button! switch (see the option setting table). After that, push the 1P button2 switch to return to the test menu screen. -|-
SWITCH TEST [— (a) Switch test screen SOUND TEST t— (b) Sound test screen COIN OPTIONS -— (c) Coin option screen (Setting of game fees) GAME OPTIONS t~ (d) Game option screen (Setting of game difficulty) UARTS TEST t~ (e)} Not used POLYGON TEST t— (f) Polygon test screen A.D.S. +— (g)Not used COLOR TEST ———————————— (h) Color test screen (for monitor adjustment) CONVERGENCE TSTE —-----_7-~ (i) Cross hatch pattern (for monitor adjustment) RS-232C TEST ———————___(j) Not used yy, (Test menu screen) ~ CO IN OPTIONS {DEFAULTS IN GREEN ] 6 GAME COST : (1 or 3) CO IN | CRED IT —--—-—___++ —- 1 D ISCOUNT TO CONT INUE : NO ————-----—_}- 2 CO IN 1 MECH VALUE :
1 COIN COUNT AS 1 COIN-——+——3 CO IN 2 MECH VALUE: | COIN COUNT AS | COIN——+——~4 CO IN 3 MECH VALUE : 1 COIN COUNT AS CO IN 4 MECH VALUE : | COIN COUNT 1 COIN AS ~ GAME OPT IONS [DEFAULTS IN GREEN ] DIFFICULTY LEVEL : MIDIUM ROUND TIM : 2 MIINUTES-——-———--—_+ CABINET TYPE : 4 PLAYERS-—--—-———MUSIC IN ATTRACT ; YES ————--— —+———5 SPEAKER 1 COIN-——+——6 UNIFORM OUT : STEREQO——-——---+ COLOR : USA BONUS FOR QUANTITY BUY IN: NONE —————--+--—- 7 CRED IT MODE : COMMON ——_-—_—____--+-—-~ 8 COIN COUNTER: TYPE A: 1 COUNTER—————————_+—9 FREE PLAY : NO 10 X / (Coin Option \ / screen) (Game Option Screen) (Option setting table) Item Contents 1. Game fees one count required for one aame (one credit) | (1 2.
DISCOUNT 50% 3. COIN 1 MECH VALUE Count per coin 1<f1- 4, COIN 2 MECH VALUE Count per coin 1<f1-91 discount when continuina a plav or 3.) <f1- 91 5. COIN 3 MECH VALUE Count per coin 1<f1-91 6. COIN 4 MECH VALUE Count per coin 1<f1- 7. BONUS One additional of coins coin per the specified number | NONE < COIN 9] 2 Coins Give 1 Coin~ 9 Coins Give 3 Coins COMMON (Credit is common to 1P, 2P,3P and 4P) <, EACH ONE (Credit is set for 1P, 2P,3P and 4P each) EACH TWO (Credit is set for 1P and 2P,3P and 4P each) 8. CREDIT MODE 9. COIN COUNTER TYPE A:1COUNTER < TYPE B :2COUNTERS 10. FREE NO< PLAY YES 11. DIFFICULTY LEVEL MEDIUM 12. ROUND TIME 2MINUTES < f1. 2.3.4.5] 13.CABINET <f EASY.
TYPE 4 PLAYERS 14.MUSIC IN ATTRACT YES < 15.SPEAKER OUT STEREO < 16.UNIFORM COLOR USA< Game fees i game 9] NO < YES [Continue < MEDIUM . HARD 1 2PLAYERS NO MONO JAPAN I 2: / 34 Credit 7 | display Example 100 yen | 100 yen 1 COIN ICREDIT | 1COUNT ICOIN | NONE | CREDITO 100 yen 2 COINS ICREDIT | YES | 1COUNT 2COINS | NONE | CREDIT 0/2 50 yen | NO -2- (Note) Set -3°,-4 corres ponded to Coin use. Mech 1&2 in we ow Dn cr
6. PC Board JAMMA Connector Table edge connector (56P 3.96 mm pitch) Solder side GND Terminal No. A Solder side 1 GND Speaker R (-) [YEL] pitch) Parts side Al Bl B2 A3 B3 A4 B4 Insertion error preventing key AS BS Insertion error preventing key Insertion error preventing 4P lever RIGHT 4P lever DOWN A6 B6— |4P lever LEFT Al B7 |4P lever UP 4P button! Ag B8 | 4P button? AY Ald Bo Bi0)| |GND [GND GND B 2 +5V Cc 3 +5V +5V D 4 +5V E 5 F 6 H 7 Insertion error preventing Terminal No.
A2 GND +12V Extended edge connector (48P 2.54 mm Parts side +12V 4P start switch Speaker R (4) [ORG | Coin counter 2 J 8 |Coin counter | Speaker (-) K L 9 10 Coin lockout 1 | Speaker (+) Audio (GND) M 11 | Audio (+) Video GREEN N 12 | Video RED Video SYNC P 13 | Video BLUE Al3_ | BI3 Service switch 14 15 16 | Video GND | Test switch |Coin switch 1 Bi4 BIS B16 {Coin switch 3 Coin switch 2 R s T Al4 Als Al6 2P start switch 2P lever UP U Vv 17 18 |1P start swich |1Plever UP AlT Als B17 BI8 |GND | GND 2P lever DOWN w 19 |1P lever DOWN 3P_button3 Ald | BI9 3P button!
A20 B20 [3P lever RIGHT 3P lever LEFT 3P lever UP B21 All A22_ | B22 |3P lever DOWN |3Pstart switch 2P lever LEFT X 20 | 1P lever LEFT 2P lever RIGHT 2P button] Y Zz 21 22 | 1Plever RIGHT |1P button! 2P button2 2P button3 a b 23 24 |1P button2 |1P button3 GND Fi e o 7 GND GNP t 28 GND - Do not connect anything to the blank connectors. - Both lockout solenoid and coin counter operate on +12V. - Connect the switches to N.O. terminals such as a microswitch, and the GND to the COM terminal. Coin switch4 All | Bil Al2 Bi2 A23 A24 /4P button3 13P button? B23 B24 * Do not connect anything to the blank connectors.
- The colors indicated in [] in the extended edge connector table show these of color cords on the extended edge connector harness in the accessories. {Connection to stereo cabinet] (I)STEREO/ MONO setting Select SPEAKER OUT in the game option screen at the test menu screen. Monophonic cabinets do output only the left-hand sound even if the stereophonic setting is selected. * The supply voltage is available within +5%. For use in the best condition, get the supply voltage as close to the specified voltage as possible.
(Recommended power capacity) +5V +5% 2.5A or more +12V 45% 2.0A or more (2) Connection to speakers - Connect the (L) speaker to the speaker output of 56P edge connector (JAMMA) on the PC board. - Connect the (R) speaker to Speaker R (+), (-) of 48P extended edge connector. * Use a DDK 225D-10024C2-2312 as a 48P extended edge connector.