Delta DVP-ES2 — 2.13 Special Data Register

DVP-ES2/EX2/SS2/SA2/SX2/SE&TP Operation Manual - Programming 2-40 OFF STOP RUN Special ES2 SA2 Latch Content SS2 SX2    Attrib. Default D EX2 SE -ed ON RUN STOP D1864* ↓ D1879* The data which is read from slave ID#13 in the PLC LINK ○ ○ ○ ○ 0 - - R NO 0 D1880* ↓ D1895* The data which is written into slave ID#13 in the PLC LINK ○ ○ ○ ○ 0 - - R/W NO 0 D1896* ↓ D1911* The data which is read from slave ID#14 in the PLC LINK ○ ○ ○ ○ 0 - - R NO 0 D1900* ↓ D1931* Specify the station number of Slaves for PLC-Link when M1356 is ON. Consecutive station numbers set by D1399 will be invalid in this case. Note that the registers are latched only when M1356 is ON.

○ ╳ ○ ○ 0 - - R/W NO D1912* ↓ D1927* The data which is written into slave ID#14 in the PLC LINK ○ ○ ○ ○ 0 - - R/W NO 0 D1928* ↓ D1943* The data which is read from slave ID#15 in the PLC LINK ○ ○ ○ ○ 0 - - R NO 0 D1944* ↓ D1959* The data which is written into slave ID#15 in the PLC LINK ○ ○ ○ ○ 0 - - R/W NO 0 D1960* ↓ D1975* The data which is read from slave ID#16 in the PLC LINK ○ ○ ○ ○ 0 - - R NO 0 D1976* ↓ D1991* The data which is written into slave ID#16 in the PLC LINK ○ ○ ○ ○ 0 - - R/W NO 0 D1994 Remaining times for PLC password setting on DVP-PCC01 ○ ○ ○ ○ 0 D1995 Data length for PLC ID Setting on DVP- PCC01 ○ ○ ○ ○ 0 - - R/W NO 0 D1996 1st Word of PLC ID Setting for DVP-PCC01 (Indicated by Hex format corresponding to ASCII codes) ○ ○ ○ ○ 0 - - R/W NO 0 D1997 2nd Word of PLC ID Setting for DVP-PCC01 (Indicated by Hex format corresponding to ASCII codes) ○ ○ ○ ○ 0 - - R/W NO 0 D1998 3rd Word of PLC ID Setting for DVP-PCC01 (Indicated by Hex format corresponding to ASCII codes) ○ ○ ○ ○ 0 - - R/W NO 0 D1999 4th word of PLC ID Setting for DVP-PCC01 (Indicated by Hex format corresponding to ASCII codes) ○ ○ ○ ○ 0 - - R/W NO 0 D6000 Axis number that has error during CANopen communication on Delta Servo V2.8 ╳ ╳ ╳ 0 - - R NO 0 D6001 Error code of CANopen communication on Delta Servo V2.8 ╳ ╳ ╳ 0 - - R NO 0 D6002 Record the STEP that error occurs duringCANopen communication on Delta Servo V2.8 ╳ ╳ ╳ 0 - - R NO 0 D6008 The PR command of the Delta CANopen communication axis 1 from the Delta servo V2.8 ╳ ╳ ╳ 0 - - R NO 0 D6009 PR command of the Delta CANopen communication axis 2 from the Delta servo V2.8 ╳ ╳ ╳ 0 - - R NO 0 D6010 PR command of the Delta CANopen communication axis 3 from the Delta servo V2.8 ╳ ╳ ╳ 0 - - R NO 0 D6011 PR command of the Delta CANopen communication axis 4 from the Delta servo V2.8 ╳ ╳ ╳ 0 - - R NO 0 D6012 PR command of the Delta CANopen communication axis 5 from the Delta servo V2.8 ╳ ╳ ╳ 0 - - R NO 0 D6013 PR command of the Delta CANopen communication axis 6 from the Delta servo V2.8 ╳ ╳ ╳ 0 - - R NO 0 D6014 PR command of the Delta CANopen communication axis 7 from the Delta servo V2.8 ╳ ╳ ╳ 0 - - R NO 0