Delta DVP-ES2 — 2.14 E, F Index Registers

DVP-ES2/EX2/SS2/SA2/SX2/SE&TP Operation Manual - Programming 2.14 E, F Index Registers Index registers are used as modifiers to indicate a specified device (word, double word) by defining an offset. Devices can be modified includes byte device (KnX, KnY, KnM, KnS, T, C, D) and bit device (X, Y, M, S). E, F registers cannot be used for modifying constant (K, H) Index registers not used as a modifier can be used as general purpose register. Index register [E], [F] Index registers are 16-bit registers which can be read and written. There are 16 points indicated as E0~E7 and F0~F7. If you need a 32-bit register, you have to designate E. In this case, F will be covered up by E and cannot be used.

It is recommended to use instruction DMOVP K0 E to reset E (including F) at power-on. 16-bit 16-bit F0 E0 Low word High word 2-42 OFF STOP RUN Special ES2 SA2 Latch Content SS2 SX2    Attrib.

Default D EX2 SE -ed ON RUN STOP (32-bit) D6052 D6053 Target position of the Delta CANopen communication axis 3 from the Delta servo (32-bit) V2.8 ╳ ╳ ╳ 0 - - R NO 0 D6054 D6055 Target position of the Delta CANopen communication axis 4 from the Delta servo (32-bit) V2.8 ╳ ╳ ╳ 0 - - R NO 0 D6056 D6057 Target position of the Delta CANopen communication axis 5 from the Delta servo (32-bit) V2.8 ╳ ╳ ╳ 0 - - R NO 0 D6058 D6059 Target position of the Delta CANopen communication axis 6 from the Delta servo (32-bit) V2.8 ╳ ╳ ╳ 0 - - R NO 0 D6060 D6061 Target position of the Delta CANopen communication axis 7 from the Delta servo (32-bit) V2.8 ╳ ╳ ╳ 0 - - R NO 0 D6062 D6063 Target position of the Delta CANopen communication axis 8 from the Delta servo (32-bit) V2.8 ╳ ╳ ╳ 0 - - R NO D9800~ D9879 They are for left-side special modules which are connected to an SA2/SX2/SE series MPU.

╳ ╳ ○ ○ - - - R/W NO 0 D9900~ D9979 They are for special modules connected to an ES2/EX2 series MPU. (Please refer to DVP-PLC Operation Manual – Modules for more information) They are for right-side special modules connected to an SA2/SX2/SE series MPU. ○ ╳ ○ ○ - - - R/W NO 0 D9980 CANopen status message code (Only for DVP-ES2-C series MPUs) ○ ╳ ╳ ╳ 0 - - R NO 0 D9981~ D9996 (Only for DVP-ES2-C series MPUs) CANopen status message code in slave station 1~slave station 16 ○ ╳ ╳ ╳ 0 - - R NO 0 D9998 Bit0~15 represent station 1~station 16. If a bit is ON, an error occurs. (It is only applicable to DVP-ES2-C series MPUs.

If DVP-ES2-C V3.24 (or above) is turned from OFF to ON, the value in D9998 will be H’0. If DVP-ES2-C V3.26 (or above) is turned from OFF to ON, the value in D9998 will be H’FFFF.) ○ ╳ ╳ ╳ H’ FFFF - - R NO 0 D9999 Showing the CAN baud rate K1: 20K; K2: 50K; K3: 125K; K4: 250K; K5: 500K; K6: 1M (It is only applicable to DVP-ES2-C V3.26 and above.) V3.26 ╳ ╳ ╳ 0 - - R NO 0 32-bit F0 E0