2 Functions of Devices in DVP-PLC DVP-PLC Application Manual 2-60 ES SA Off STOP RUN EH2 EH3 Special D Function EX SX Attribute Latched Default SV SV2 SS SC On RUN STOP D1151 Table counting register for DHSZ multiple set values comparison mode ╳ ╳ ○ ○ 0 0 0 R NO 0 D1152 High word of changed D value for DHSZ instruction ╳ ╳ ○ ○ 0 0 0 R NO 0 D1153 Low word of changed D value for DHSZ instruction ╳ ╳ ○ ○ 0 0 0 R NO 0 D1154* Suggested deceleration time interval (10 ~ 32,767ms) for adjustable acceleration/deceleration pulse output Y0 (Not available in SX V3.0 and above) ╳ ○ ╳ ╳ 200 - - R/W NO 200 Pulse number for masking Y4 (Low word) ╳ ╳ ○ ○ 0 0 - R/W NO 0 D1155* Suggested deceleration frequency (-1 ~ -32,700Hz) for adjustable acceleration/deceleration pulse output Y0 (Not available in SX V3.0 and above) ╳ ○ ╳ ╳ -1,000 - - R/W NO -1,000 Pulse number for masking Y4 (High word) ╳ ╳ ○ ○ 0 0 - R/W NO 0 D1156 ↓ D1159 Designated special D for RTMU, RTMD instructions (K0~K3) ╳ ╳ ○ ○ 0 - - R/W NO 0 D1160 Designated special D for RTMU, RTMD instructions (K4) ╳ ╳ ○ ○ 0 - - R/W NO 0 Low word of the present output pulse frequency of CH0 (Y0/Y1) ╳ ╳ ╳ V1.62 0 - - R/W NO 0 D1161 Designated special D for RTMU, RTMD instructions (K5) ╳ ╳ ○ ○ 0 - - R/W NO 0 High word of the present output pulse frequency of CH0 (Y0/Y1) ╳ ╳ ╳ V1.62 0 - - R/W NO 0 D1162 Designated special D for RTMU, RTMD instructions (K6) ╳ ╳ ○ ○ 0 - - R/W NO 0 Low word of the present output pulse frequency of CH1 (Y2/Y3) ╳ ╳ ╳ V1.62 0 - - R/W NO 0 D1163 Designated special D for RTMU, RTMD instructions (K7) ╳ ╳ ○ ○ 0 - - R/W NO 0 High word of the present output pulse frequency of CH1 (Y2/Y3) ╳ ╳ ╳ V1.62 0 - - R/W NO 0 D1164 Designated special D for RTMU, RTMD instructions (K8) ╳ ╳ ○ ○ 0 - - R/W NO 0 Low word of the present output pulse frequency of CH2 (Y4/Y5) ╳ ╳ ╳ V1.62 0 - - R/W NO 0 D1165 Designated special D for RTMU, RTMD instructions (K9) ╳ ╳ ○ ○ 0 - - R/W NO 0 High word of the present output pulse frequency of CH2 (Y4/Y5) ╳ ╳ ╳ V1.62 0 - - R/W NO 0 D1166* Switching rising-/falling-edge counting mode of X10 (available in SC V1.4 and versions above) ╳ ○ ╳ ╳ 0 - - R/W NO 0 _ Low word of the present output pulse frequency of CH3 (Y6/Y7) (EH3/SV2 V1.62 ~ V1.84) ╳ ╳ ╳ V1.62 0 - - R/W NO 0 D1167* Switching rising-/falling-edge counting mode of X11 (available in SC V1.4 and versions above) ╳ ○ ╳ ╳ 0 - - R/W NO 0 _ High word of the present output pulse frequency of CH3 (Y6/Y7) (EH3/SV2 V1.62 ~ V1.84) ╳ ╳ ╳ V1.62 0 - - R/W NO 0 D1168 Interruption request for receiving specific word in RS instruction (I150) ╳ ○ ○ ○ 0 - - R/W NO 0 D1169 Interruption request for receiving specific word in RS instruction (I160) ╳ ╳ ○ ○ 0 - - R/W NO 0 D1170* PC value when executing single step ╳ ╳ ○ ○ 0 0 0 R NO 0 D1172* Frequency of 2-phase pulse output (12Hz ~ 20kHz) (Not available in SX V3.0 and above) ╳ ○ ╳ ╳ 0 - - R/W NO 0 D1173* Modes of 2-phase pulse output (K1 and K2) (Not available in SX V3.0 and above) ╳ ○ ╳ ╳ 0 - - R/W NO 0 X4 speed detecting value ╳ ╳ ○ ○ 0 0 - R/W NO 0 D1174* Low 16 bits of target numbers of 2-phase output pulses (Not available in SX V3.0 and above) ╳ ○ ╳ ╳ 0 - - R/W NO 0 X10 speed detecting time ╳ ╳ ○ ○ 0 0 - R/W NO 0