E54 Motor relay contacts sticking Circuit board faulty; Current leakage from motor or wiring. E62 Overheating during washing NTC sensor faulty; Heating element faulty; Wiring faulty; Circuit board faulty. E66 Power relay for heating element faulty Circuit board faulty; Current leakage from heating element or wiring to ground. E82 Error in reset position of selector Circuit board faulty. E93 Incorrect machine configuration Configuration data incorrect; Circuit board faulty. E94 Incorrect washing cycle configuration Configuration data incorrect; Circuit board faulty. E95 Communications error between microprocessor and EEPROM Circuit board faulty.
E96 Incongruence between hardware version and configuration. Configuration data incorrect; Circuit board faulty. E97 Incongruence between programme selector and cycle configuration Configuration data incorrect; Circuit board faulty. EB1 Power supply frequency of appliance incorrect Mains power supply problems (incorrect / interference); Circuit board faulty. EB2 Voltage too high Mains power supply problems (incorrect / interference); Circuit board faulty. EB3 Voltage too low Mains power supply problems (incorrect / interference); Circuit board faulty.
Alarm Description Possible fault QUICK GUIDE AND APPLIANCES LIST 9/176 E61 Insufficient heating during washing NTC sensor faulty; Heating element faulty; Wiring faulty; Circuit board faulty. E71 NTC washing sensor faulty NTC sensor faulty; Wiring faulty; Circuit board faulty. E83 Error in reading selector position Configuration data incorrect; Circuit board faulty. 1.6.1 Notes concerning certain alarm codes ѓ Configuration alarms E93-E96: ѓ Configuration alarm E94: alarm display” function cannot be used. ѓ Alarms EB1-EB2-EB3: the abnormal situation has ceased. ѓ Alarms E51- E52: switch the appliance OFF by turning the selector to position “0” (reset).
EWM1000 Alarm Description Possible fault Action/Machine status Reset E54 Motor relay contacts sticking Circuit board faulty; Current leakage from motor or wiring. Cycle blocked, door closed (after 5 attempts in diagnostics or immediate during selection) Selector on “0” E61 Insufficient heating during washing NTC sensor faulty; Heating element faulty; Wiring faulty; Circuit board faulty. Heating phase skipped --- E62 Overheating during washing NTC sensor faulty; Heating element faulty; Wiring faulty; Circuit board faulty.
Safety drain (with cooling water fill) - Stop with door open Selector on “0” E66 Power relay for heating element faulty Circuit board faulty; Current leakage from heating element or wiring to ground. Safety drain (with cooling water fill) - Stop with door open Selector on “0” E71 NTC washing sensor faulty NTC sensor faulty; Wiring faulty; Circuit board faulty. Heating phase skipped --- E82 Error in reset position of selector Circuit board faulty. Cycle cancelled Selector on “0” E83 Error in reading selector position Configuration data incorrect; Circuit board faulty.
During the cycle continues normally, switches off completely during selection --- E93 Incorrect machine configuration Configuration data incorrect; Circuit board faulty. Appliance blocked Selector on “0” E94 Incorrect washing cycle configuration Configuration data incorrect; Circuit board faulty. Appliance blocked Selector on “0” E95 Communications error between microprocessor and EEPROM Circuit board faulty. Appliance blocked Selector on “0” E96 Incongruence between hardware version and configuration. Configuration data incorrect; Circuit board faulty.
Appliance blocked Selector on “0” E97 Incongruence between programme selector and cycle configuration Configuration data incorrect; Circuit board faulty. Appliance blocked Selector on “0” EB1 Power supply frequency of appliance incorrect Mains power supply problems (incorrect / interference); Circuit board faulty. Cycle blocked until normal power supply conditions are restored Selector on “0” EB2 Voltage too high Mains power supply problems (incorrect / interference); Circuit board faulty. Cycle blocked until normal power supply conditions are restored Selector on “0” EB3 Voltage too low Mains power supply problems (incorrect / interference); Circuit board faulty.
Cycle blocked until normal power supply conditions are restored Selector on “0”