US Army Materiel Command AMCP 706-197 — AMCP 706-197 Reliability Prediction Handbook — US Army Engineering Design Guide PDF

Downloaded from https://www.everyspec.com AMCP 70-117 CHAPTER 7 KINDS OF REDUNDANCY AND REPAIR 7-1 INTRODUCTION If a system contains any redundancy, the question arises, "How does one know that Redundancy and repair are very similar each unit is good?" Just knowing that the concepts. In the general case where switching system is up is not enough, since some units is not instantaneous it is easy to visualize two could be bad and the system would still be similar operations, one called redundancy and up. Therefore, there must be checkout of one called repair. In redundancy, the time each unit in the system.

This involves hard- used to replace a faulty unit is usually shorter ware, software, time, and money. Checkout is than the time a repair is considered to take. rarely perfect. Will the analysis take that into There are many important considerations account? The knowledge of system state at in a redundancy/repair situation, i.e., "time = zero" is also important because in 1. In what state are all the units at t = 0? many analyses, a system or unit is presumed How does one know? Is checkout perfect? tj be good-as-new viz., "time = zero" again good-as-new? How does one know? Is check- There are only two tractable choices in out perfect? deciding the condition of a unit after repair: 3.

In what state is a repaired system? good-as-new and bad-as-old. Good-as-new of- How does one know? Is checkout performed? ten is taken to mean "perfect", but if check- Is it perfect? out is involved all it means is that time reverts 4. What kinds of failures are being allevi- to zero for the unit that is good-as-new. The ated? If failures are due to the rare, random phrase bad-asold was coined to contrast with occurrence of severe conditions, redundancy good-as-new and to illustrate the condition might not be of much help. where the failure rate of the system "immedi- 5. How difficult is it to know that a unit ately after a repair" is the same as it was "just has failed?

How difficult is it to remove the before repair". An internal combustion engine faulty unit and replace it? after a miner tune-up is a good illustration of 6. How much of an improvement in reli- bad-as-old. The major components of the en- ability is needed or expected? What reliability gine didn't change; perhaps all that was done measure is important in your case? For exam- was to clean and regap the spark plugs, and ple, mean time to failure is not a good reliabil- adjust the distributor gap and the timing. The ity measure for short times. engine certainly is not good-as-new. A Poisson 7.

How much does redundancy/repair process with nonconstant rate is an example cost in weight, dollars, volume, design effort, of the bad-as-old behavior. checkout, schedule time, heat dissipation, When the failure rate of each unit is con- system complexity, extra connectors, etc.? stant, there is no difference between bad-as- 8. What about switching? Is information old and goL i-as-new. lost during switching? 2. In what state is a repaired unit? Is it after repair. 9. What about the failure behavior of In theoretical analyses with complicated standby equipment? system-states a common assumption is that 10.

Under what conditions are failures the repaired unit is good-as-new, but the other s-independent? When the correct calculations units are bad-as-old. Of course, because of have been made, how much improvement in tractability considerations, failure rates of haebeen mad, thow much imunits are assumed most commonly to be con- stant so that any time the system is known to 7-2 KNOWLEDGE OF SYSTEM STATE be working, it is good-as-new. Many papers require that the assumptions be inferred from In order to analyze a system, one needs to the mathematics; the authors have been re- know the state (condition) of the system at miss in stating assumptions. zeveral time instants.

The two most important Many systems use periodic checkout to as- instants are "time = zero" and "just after re- certain the state of the system. Preventive pair". maintenance is performed as required. But 7-1