Downloaded from https://www.everyspec.com AMCP 706-260 the other engages the projectile just ahead of the round follows to lift the pawl, the dog remains rotating band. As the belt and ammunition move with undisturbed and holds the last round at the mouth tho tarwho.I. frinet cAs wedae between the entrance. but at a position low enough to clear the cartridge case and the clamps of the belt links and pry starwheel. If the last round should be able to drop to the links off the case. The freed single end of the link, the top of the bolt ai the next-to-last round is fired, w.ttt ;* .. ,4 .vv1 ..
tth..,, *,t th,4 .,,tr, iq e,4wtiv- ccnntrnl nvor it it lot thereby increasina guidcd by the link deflector into the ,k .hute. the probability of jamming. But, since it is held, the Freeing the double end releases the link completely counterrecoiling bolt merely closes on an empty from the belt. The detached link fails through the link chamber. Action resumes when the first round of a chute for retrieval or discard. Meanwhile, the link-free new belt reaches the control pawl. round, guided by outer cover and starwheels, continues on its circular path.
As it approaches the feed mouth, 7-2.3.2 Eleelaly Driven Fad Mechanism the round begins to fall away from its cradled position In th= starwhesls and into the lceor contour of the The round and link control of an electrically driven cartridge guides (Fig. 7-12 (B)). The guides compleze feed mehaism consists of two operating units, the feed the path to the feed mouth entrance. Before reaching whee unit and the operating lever unit. The feed wheel the mouth, the round contacts the spring-loaded, unit contains two feed whee , two loading levers, u .nd a cartridge holding cants. Forced by the sag tooth cf bank of three link strippeis.
The operattng lever unit each starwheel, the round pushes the holding cams contains two operating levers, two loading guides, and aside and enters the mouth. As the lag teeth ride over one round retaining Anger. The related componens the round, gaps between round and cam surfaces occur between these two usits axe shown schematically in Fig to permit the cams to swing back to eatablish contact 7-13 where the round is used as a comnion reference. between cam surface and round (Fig. 7 -12 (5)).
The Loading lever and retaining finger are spring loaded; the spring loads on the cam force the round downward spring force to the loading lovcr is transmitted by the and slmultanoously prevent it from reversing its operating lever. The retaining finger has its owti spring. direction. The round continues downward until it alights on top The electric motor turns the feed wheel risaft through of tht, bolt which is locked in the fuing position, It a gear and clutch system. The two feed wheels draw the remains in this position until the chambered round is belt of ammunition into the fe )der at the stripper fired and the bolt recoils. The round now moves to the location (Fig. 7-14 (A)).
The link stripper rotates with bottom of the mouth where it is retained by a the feed wheel shaft and its three segments contact the constriction in the mouth. Thts constriction, or way, is crimp between tle leading double and lagging single end sloped forward at an angle of about three degrees. The of the link. The prying action crf the link stripper force round is held in dsh position by the varti.ai component on the link crimp and the stnzpper cover reaction maps of the starwheel force transmitted by the round the double end of the link off the lead round (Fig. 7-14 following. While cowsterrecollIng, the bolt contacts the (B)).
But the single end of the link is still attached to the lower portion of the cartridge case base and drives &e la round. However, continued action of the stripper on round toward the chamber; the three-degree slope the cri-np guides the link into the link chute while the prescribes the dedred projectile feed path. As the round freed round continues on its circular path, guided by the clears the ways it is forced downward to become feed wheel and link chute support (Fig. 7-14 (C)). As correctly aligned with the bolt. Its former space is now the anmunition belt continues to advance, the prying occupied with the next ruund.
action of the chute on the double end, conbined with the restriction imposed cn the lag round by feed wheel and chute support, releases the single end from the Just prior to entering the feed mouth, ile found csthe or round, permitting the now freed link to fall through the contacts the lower edge of the spring-locurd cartridge tLik chute. control pawl (Fig. 7-12 (C)). Continued round travel radss the pawl which in turn lifts the holdin dog.
The freed round .ontinues along the curved chute This action removes the 'obstruction that the normal Pipport until it reaches the entrance to the feed mouth position of the dog provides and ives free access at where it contacts the loading guides on the opposite side the feed mouth entrance to the preceding round. This of the mouth. These guides form the path for the round process is continuous for the entire length of the as it moves into the mouth. Here the round contacts the anmunition belt except for the last found. Beciuse no loading jevers and retainivg finger. As the feed wheel 7-12