N/A (no manufacturer mentioned) N/A — MIL-HDBK-304C Package Cushioning Design Handbook PDF Download

MIL-HDBK-304C 6.1.2 Material identification. For convenience, the materials for which stress-strain, peak acceleration-static stress curves, and transmissibility curves which are referenced in Appendices A-C are identified by the following numbers. (See Table VIII).

TABLE VIII Appendices A-C Materials Listing NUMBER MATERIAL DENSITY (pcf) (kg/m 3 ) 1 Polyurethane-Ether (MIL-PRF-26514) 1.5 24.0 2 Polyurethane-Ether (MIL-PRF-26514) 2.0 32.0 3 Polyurethane-Ether (MIL-PRF-26514) 4.0 64.0 4 Polyurethane-Ester (MIL-PRF-26514) 1.5 24.0 5 Polyurethane-Ester (MIL-PRF-26514) 2.0 64.0 6 Polyurethane-Ester (MIL-PRF-26514) 4.0 64.0 7 Bound Fiber (Rubberized Hair) PPP-C-1120 Type II 8 Bound Fiber (Rubberized Hair) PPP-C-1120 Type III 9 Bound Fiber (Rubberized Hair) PPP-C-1120 Type IV 10 Polyethylene Foam (PPP-C-1752) 2.0 32.0 11 Polyethylene Foam (PPP-C-1752) 4.0 64.0 12 Polystyrene Foam (PPP-C-850) 1.5 24.0 13 Polystyrene Foam (PPP-C-850) 2.5 40.0 14 Polyethylene, Chemically Crosslinked 2.0 32.0 15 Convoluted Ether Polyurethane-1", 2", 3" 1.1 17.6 16 Convoluted Ether Polyurethane 2", 4", 6" 1.1 17.6 17 Convoluted Ether Polyurethane-1", 2", 3" 1.5 24.0 18 Convoluted Ether Polyurethane-2", 4", 6" 1.5 24.0 19 Cellulose Wadding 20 Air Encapsulated Film, .5" ply thickness 0.69 11.0 (PPP-C-795) 21 Hexagonal Film, Open Cell 1.40 22.4 (PPP-C-1842) 22 Hexagonal Film, Reinforced 1.80 28.8 Cell (PPP-C-1842) 6.1.3 Select cushioning application method.

Once the designer has made an initial estimate of the amounts of different kinds of cushioning that will protect the item, their next step in the design should be to compute the cost (see paragraph 5.7) related to the use of the different materials and application methods. The designer can then select the most suitable material and application method. Some of the most common application techniques involve complete encapsulation, corner pads, and face pads. These and various other application techniques are discussed in the paragraphs and sub-paragraphs of 6.3. 6.1.4 Check for buckling (if pertinent).

Long, slender cushions may tend to buckle, instead of becoming uniformly compressed, when subjected to a compressive force applied along the lengthwise axis of the cushion. Generally, this is undesirable because the item might tip (Figure 6-3) and become damaged as a result of collision of the item with the container. (NOTE: Under certain circumstances, controlled buckling in cushioning can be desirable). For impacts where buckling occurs, the data from Peak Acceleration--Static Stress cushioning curves becomes invalid and damage is likely to occur. In order to preclude the chance of buckling, if the designer 41 Downloaded from https://www.everyspec.com