Downloaded from https://www.everyspec.com AMCP i66-210 -- 2.1 ENVIRONMENTAL FEATURES when subjected to-theproperi target.conditions. The tactical situation often requifes~the use of a Tactical requirements vary -fgr specific fuzes, very sensitive explosive train-one that responds but every fuze will undergo a number of-environ- to small impact forces, to heat, or to electrical mnental .conditaons: from assembly to. 5 use. While energy.
Another of the designer's important con- all fuzes do-not undergo the same environmental siderations is- safety in -manufacture, in-loading, conditions, the -more common areas' have- been in transportation, in storage, and-in assembly to 'standardized, and g6uped together -for, cdfiven- the munition. In some cases, the forces against ience j. Accordingly, the specifications foi new whichItlie fiize must be protected may be greater fuzes can be written simplyby reference. The en- than, the target stimulus. Safety then is a real, vironmental conditiohs influence choice,of-mate- challenge for the designer. No 5 phase canobe-ig- rials,.
iiethod lof sealing-and'pr6tebting the fuze, noted because an unsafe fuze may become a ayotit and design of component-parts and subtle weapon for the enemy. -method of packaging. Many of the-Pwidely used A fuze designer knows thesafety requf,- ,features- are included'in, the following, list (for. -rents; these govern tht approach he takes. At , more details, see pars. 15-3 and 15-4): each step-in design-and developmenteof a ,fuze, (1) OPERATING TEMPERATURE.Thefuze lie--must be conscioiis,,of-safet y.
Safety applie- must-withstand temperatures ranging from an air not only to the complete fuze but also to each, temperature of 125F (ground temperature, of step during-processing and assembly of-the vari- 145F)in-hot-dry climates to-an air temperature pus components of the explosive strain. If the of -50°F (ground temperature of -65"F 1 ) 'in requisite detonator cannot be manufactured cold-climates'. Temperatures can drop to -80 F safely, then the design of the fuze-may~have to- ,in bomb-bays of.'high flying aircraft,,and aero- be changed.
dynamic, heating can raise the temperature of 'Safety enters every ,facet of iuze and compoz missiles launched-fromohigh speedplanes above nent development. In additionsto the broad as- 1450F. pects, there are safety features infuzes that are (2) STORAGE TEMPERATURE. The 'fuze mandatory, desrabl , or' both. Frequentiy, 4he, must be capable of-withstanding storage teiper- desirable features can: be included at the de- atures from :-70 to 160 F and be -operable signer's discretion without interfering with the after removal from storage',. basic design. It should be noted that these (3)- HUMIDITY.
The fuze, must withstand "extra" features represent the designer's-com relative humidities up to 100%. petenco and ingenuity. (4) RAIN. The fuze must function as in- A tcardinal requirement for- all' fuzes is that tended even whenfired in a rain storm. they be detonqtor safe,, i.e., functioning~of the (5) WATER. The fuze -may, -in certain in- detonator cannot initiate subsequent explosive stances, be required to be waterproof, showing train components prior to arming.
An inter- no leakage, and be safe and operable after immer- rupted explosive train (mechanicafseparation) i's sion-in wvater at 700 ± 100 F under a- gage pres- the basic method for attaining thedetonator safe sure of 15 + 5 psi for one hour. feature. Examples are out-of-line eleients such. (6) ROUGH TREATMENT. The fuze must as a slider or a rotor. The interrupter should, withstandthe rigors of transportation (including have a positive lock- while in the safe position. perhaps parachutedeiivery), and rough handling. The detonator must be assembled'in the safe po- (7) FUNGUS:Thefuze must be able to with- sition so thatthe fuz-is safe during, all:final as- stand fungus growth.
sembly steps and during subsequent -handling. (8)- SURVEILLANCE. The fuze must remain Artillery projectiles, mortar projectiles, and safe and operable during and after storage in a rodcts must-be bore safe.:The fuze must be so sealed' can for 10 years (20 years are desired). designed that the detonator will not initiate a - bursting charge while the projectile -or rocket is - 9-2.2 GENERAL SAFETY FEATURES in the launching tube. Hence, it may be neces- sary to add a device to delay the ar Ming, of the The basic mission ofa fuze is to function re- fuze until after the munition has left the liably, and to, receive and amplify a stimulus launcher. 9-2