Downloaded from https://www.everyspec.com -~ AM60-706-210, S'- -: material, mustnot causeparicle or organic con- electric and-prximity fuzes, have a number of laination- of electrical con cts (see-pr. 14-2)- desirable properties. Some-of these-are: noF-fouling or. corrosion of other fuze parts. (1) They- can be usedrto join metas at reia- 0 - (5) Temperature. tively ow emperatures.. Nosealant or sealing material'has all the qu4i- (2) hey can Withstand-c6nsiderable bend- ties requied.The problem, the, -is to choose the, ing without fracture. best combination- of characteristics.
Choice is, (3) ,;They ban usually .be applied by simple usually basd-primarily - on ,the overall physical means h ' be usddwith metalshving rea- and- chemical properties of the materiidl and- tively low melting,points., ' secondarily 6n -its aging properties. Other-things The ni6st-commonly, used soft solders are tin- to be considered before a final decision is made lead-alloys. Thse soft solders; have the primary are availability of materials, cost, ease ofapplica- disadvanage tat h-ey have .low 'sirength, com- tfon, txicity, useful pot life, and service-life?, paired with the metas usually joined.
Character- The mateials commonly Used, asfsealants in- istics of soft solder alloys are shown -in, Table -lude- ,various rubbers, neoprene,, polyesters, 14-2." alkyds,. phenolics, vinyls;, and flexible epoxy Conductive adhesives can sometimes, be, used, resins". No? sealant has,-been found Which will in applieatiofiswhere heatgenerated during the pro4ue-a-joint as tight-as-a- well-soldered joint: soldering process might damage temperatue- - The designer, should look to the present ef- sensitive components. Ty ,pical applicationsbin- -fort made to apply-one-componentsealers soas, clude bonding barium titanate elements together to avoid pot iife problems.
or to ferrite rods, making electrical donnections ,to battery- terminals,, and repairing printed cir- P:LYETHYLENE: cuits. NOSE CUP, 146 -CONSTRUCTION TECHNIQUES B ASE GASKET Two -important aspDects muist be colnsidered in he_ design-of a fuze.-First, the componentsmust be selected and incorporated into the fuze in - ,A*ASN6R NG such ,a manner'that they will- perform ttheir in- .. m- 8s'tended 'function- properly. Second, the -com- :ppnents must be assembled into;the complet6d- fuze so a 's to maintaini their. integity, their re- lationship with oneT-another, and-their function- -ng, reliability in spite of-the extremeeiviron- -ment. to which they are subjected.
This-seond - aspect requires unusual care-in the construction 4 T and assembly of the fuzes, in order to assure ,RING proper performance. -9 144.1- MECHANICAL CONSIDERATIONS NOTE' RINGS COATED"WITH OW-CO*NINGT*Pf O Thepermissible volume and weight of the, fuze SILICONE GREASE OR EQUAL' and its, location -are generally specified at the 2 Figure 14-3. Location of Seals. in a Typical start of a program. The anticipated fuze enviion- Electronic Fuze ments'during operational'use and during storage, handliigi andtrafisporation are also specified. - 14.5:3-SOLDERS These environments, paiticulariy :any unusual, ones, must be kept in mind from thestart of a C, N " -Solders are:
one of-the more troublesome en- fuze program. gineering materials" , ' 0 The two general.classes When designing hoUsihgs,-packages,,and other offsblder, are soft sol der and hard solder: mechanical parts of a fuze, it is not' sufficient to Soft splders, which are used extensively in Consider only the mechanical requiremfents for 9 445 F,+ . .. .. - __+. . ;. . . -. --. +- - .. +. . - +- .. 9-4+ _ . . . .. ..... ,