Downloaded from https://www.everyspec.com AW MC70210 4-3 INITiAL EXPLOSIVE COMPONENTS 4-3.1.2 Prcassion Primema Percussion primers differ from stab initiators in that they are initiated and fired without punc- 4-3.1 GE"JERAL CHARACTERISTICS turing or rupturing their containers. They are therefore used in fuzes mainly as initiators for It has been convenient to use the term initiat,,r obturated (sealed) delay elements. The essential to refer to a class of devices including primers, components of a percussion primer are a cup, a detonators, and several special devices that are all thin layer of priming mix, a sealing disk and an in"ial explosive components. anvil.
Initiation is accomplished by a blunt firing A primer is a relatively small, sensitive explo- pin which squeezes the priming mix between cup sive component used as the first element in an and anvil. Typical percussion primers are shown explosive train. As such it serves as an energy in Fig. 4-4(B) and (C). In general, they are less e transducerconertin uc tsrvas an mehanil sensitive than stab initiators (12 in.-oz is a typi- transducer, converting electrical or mechanical cal "all-fire" point). Percussion primer cups are energy into explosive energy.
In this respect, constructed of ductile metals, commonly brass, then, the primer is unique among the other ex- in order to avoid rupture by the firing pin. plosive components in a train. A primer, which is loaded with sensitive mate- 4-3.1.3 Flash Detonators rial, has a relatively small explosive output. It Flash detonators are essentially identical in may not detonate, but it may induce detonation construction to stab initiators. They are sensi- in succeeding components of the train. Some- tive to heat. A typical flash detonator is shown times, however, the purpose of a primer is per- in Fig. 4-4(D).
Flash detonators are considered formed, for convenience in fuze design, by other to be initiators for convenience of grouping even components such as an electric detonator. though they are not the first element in the ex- A detonator is a small, sensitive, explosive plosive train. component that is capable of reliably initiating high order detonation in the next high explosiv 4-3.1,4 Electric Initiators element in the explosive train. It differs from a Electric primers and electric detonators differ primer in that its output is an intense shock from stab initiators in that they contain the ini- wave. It can be initiated by nonexplosive energy tiation mechanism as an integral part.
They con- or by the output of a primer. Furthermore, it stitute the fastest growing class of explosive will detonate when acted upon by sufficient initiators (see also par. 4-4.5.2). heat, mechanical, or electrical energy. Several types of initiation mechanisms are Primers and detonators are commonly placed commonly employed in electric initiators: hot into two groups, namely mechanical and electri- wire bridge, exploding bridgewire, film bridge, cal. Electrical includes those which are initiated conductive mixture, and spark gap. Typical elec- by an electric stimulus while all others are me- chanical. Therefore, the mechanical group in- tric initiators are shown in Fig. 4-5.
Electrical cludes not only percussion and stab elements contact is by means of two wires, by center pin which are initiated by the mechanical motion of and case, or occasionally by two pins. a firing pin but also flash detonators which are To describe the construction, let us exanine a included because of their similarity in construc- wire lead initiator. Two lead wires are molded tion and sensitivity. As a group, electrical ini- into a cylindrical plug, usually of Bakelite, so that tiators are more sensitive and difter from the the ends of the wire are separated by a con- mechanical group in that they contain the ini- trolled distance on the flat end of the plug.
This tiating mechanism, the plug, as an integral p oa. The paragraphs which follow describe the com- gap can then be bridged with a graphite film or a mon initiator types. bridgewire. 4-3.1.1 Stab Initiators 4-3.1.6 Squibs The stab initiator is a rather simple item con- Metal parts of squibs are identical to those of sisting of a cup loaded with explosives ard coy- electric iitiators. A typical squib is shown in ered with a closing disk. It is sensitive to me- Fig. 4-6. A low explosive, flash charge is provided chanical energy. A t:m-ical stab detonator is to initiate the action of pyrotechnic devices (see shown in Fig. 4-4(A). also par. 4-4.5.2).