136 стр.
Hantek · 2 стр.
HT500B Manual
Related manuals
Contents
Document text
N2140-92000_inside
The probe cable is a sensitive part of the probe and, therefore, you should be careful not to damage it through excessive bending or pulling. Avoid any mechanical shocks to the product to guarantee accurate performance and protection. Do not use the probe assembly if the red wear indicator in the cable has become visible. Some of the probe tips / accessories are very sharp. You should handle these with care to avoid personal injury. Use only Grounded instruments. Do not connect the probe’s ground lead to a potential other than earth ground. Always make sure that the probe and oscilloscope are grounded properly.
Connect the probe to the oscilloscope and connect the ground lead to earth ground before connecting the probe to the circuit under test. Disconnect the probe input and the probe ground lead from the circuit under test before disconnecting the probe from the oscilloscope. Indoor Use Only. Do not operate in wet / damp environments. Keep product surfaces dry and clean. Do not operate in an explosive environment. Safety and Regulatory Information The CE mark is a registered trademark of the European Community. ISM GRP 1-A denotes the instrument is an Industrial Scientific and Medical Group 1 Class A product.
ICES/NMB-001 indicates product compliance with the Canadian Interference-Causing Equipment Standard. This symbol indicates the Environmental Protection Use Period (EPUP) for the product’s toxic substances for the China RoHS requirements. CAT II IEC Measurement category II is for measurements performed on circuits directly connected to the low voltage installation. Example. Household appliances portable tools, and similar equipment. If your probe requires cleaning, disconnect it from the instrument and clean it with mild detergent and water. Make sure the probe is completely dry before connecting it to the instrument. Qingdao Hantek Electronic Co., Ltd.
Hantek HT300B and HT500B Passive Probes Quick Start Guide 2 3 1 4 6 5 7
N2140-92000.5-2-16.newest
The Hantek HT300B 300 MHz and HT500B 500 MHz passive probes are high impedance probes with switchable attenuation ratio (1:1 and 10:1). These are compatible with hantek digital storage oscilloscopes or similar oscilloscopes with 1 Mohm BNC input. The BNC connector of these probes has a pin hole without a pin. This is as per the design and does not indicate any damage or fault in the probe.
Pin hole without a pin BNC Connector Table 1 - Probe and its Supplied Accessories Quantity ID Part For HT500B For HT300B Passive probe 1 1 Ground Spring 1 1 Ground Lead 1 1 Adjustment Tool 1 1 Hook Tip 1 1 Protective Cap 1 1 Channel each color with two Identification rings rings These probes have been designed and calibrated for use with instruments having an input impedance of 1M Ω paralleled by 20pF. However, these may be recalibrated for use with instruments having an input capacitance of 15 to 40pF. Adjusting Probes for Low-Frequency (LF) Compensation The probe should be adjusted for LF compensation when it is connected to an oscilloscope input for the first time.
LF compensation matches the probe cable capacitance to the oscilloscope input capacitance. This matching assures good amplitude accuracy from DC to the upper bandwidth limit frequencies. A poorly compensated probe clearly influences the overall system performance (probe and oscilloscope) and introduces measurement errors resulting in inaccurate readings and distorted waveforms. To perform LF compensation: 1 Connect the probe to the oscilloscope’s front-panel calibration output (a square wave label is usually seen near this output). 2 Use the supplied adjustment tool to adjust the LF compensation to an optimum square wave response as shown in the figure below.
Undercompensated Overcompensated Optimum Table 2 - Electrical Characteristics Characteristic Value Attenuation Ratio 1:1 / 10:1 Input Capacitance 1:1 - 100pf 10:1 - 15pf Compensation range (when terminated 15pf - 40pf into 1 Mohm) Input Resistance 1:1 - 1MΩ 10:1 - 10MΩ Maximum Input 1:1 - 150V rms CAT II Voltage 10:1 - 300V rms CAT II For HT300B For HT500B Bandwidth 1:1 - 6 MHz 1:1 - 6 MHz 10:1 - 350 MHz 10:1 - 500 MHz Table 3 - Physical & Environmental Characteristics Characteristic Value Probe Body 95mm Cable Length 1200mm Weight 55g Temperature -10 °C to +55 °C (Operating) -40 °C to +70 °C (Non-operating) Altitude 3,000 m (9,842 ft) (Operating) 12200 m (40,026 ft) (Non-operating) Humidity 5% to 95% RH up to 30 °C (Operating) 5% to 65% RH above 30 °C up to 55 °C