Index Motor Rated Slip............................................................. 174 Motor Rotates After the Drive Output is Shut Off ...................... 137 Motor Rotates Faster Than the Frequency Reference................... 136 Motor Rotates in One Direction Only............................... 135, 138 Motor Stalls During Acceleration or With Large Loads ............... 135 Motor Stops During Acceleration or When a Load is Connected..... 138 Motor Wiring...................................................................38 Multi-Function Analog 1 (Terminal AM Monitor Selection)..........
177 Multi-Function Digital Inputs................................................40 Multi-Function Digital Input Terminal S1 Function Selection ........ 175 Multi-Function Digital Input Terminal S2 Function Selection ........ 175 Multi-Function Digital Input Terminal S3 Function Selection ........ 175 Multi-Function Digital Input Terminal S4 Function Selection ........ 175 Multi-Function Digital Input Terminal S5 Function Selection ........ 175 Multi-Function Digital Output ...............................................41 Multi-Function Input Selection Error ..................................... 132 Multi-Function Input Setting Error........................................
122 Multiple Drive Wiring ........................................................39 Multi-Step Speed Reference................................................ 175 Phase Order Selection....................................................... 171 Poor Speed Control Accuracy.............................................. 136 Power Specifications 200 V Class Models............................... 163 Power Specifications 400 V Class Models............................... 164 Previous Fault ................................................................ 182 Programming Mode ......................................................
57, 58 Protective Covers, Reattaching ............................................ 158 Protective Covers, Removing ..........................................36, 158 PWM Feedback Data Fault................................................. 121 PWM Feedback Fault ....................................................... 124 R RAM Fault.............................................................. 121, 123 Rated Frequency ....................................................... 163, 164 Rated Output Capacity (kVA) ............................................. 163 Rated Voltage ..........................................................
163, 164 REMOTE .......................................................................60 Replacement Parts ..................................................... 144, 168 Restart Enabled .............................................................. 176 Reverse Direction............................................................ 176 Reverse Operation Selection ............................................... 171 Reverse Run Command (2-Wire sequence).............................. 176 RTS Control Selection ...................................................... 177 Run Command/Frequency Reference Source Selection Error.........
132 Run Command at Power Up................................................ 171 Run Command Input Error ................................................. 122 Run Command Selection ............................................. 134, 171 Run Command Selection during Program................................ 171 Run Command Selection Error ............................................ 122 N NEMA Type 1................................................................ 157 Noise From the Drive or Output Lines When the Drive is Powered On ..................................................................................
136 No-Load Operation............................................................64 Normal Duty Ratings........................................................ 162 Number of Auto Restart Attempts......................................... 178 O Open-Chassis IP20 ............................................................28 Operating with the Load Connected.........................................65 Operation Errors ....................................................... 121, 122 Operator Connection Fault ................................................. 121 Operator Programming Errors .............................................
132 Option Disconnected ........................................................ 121 Option Unit External Fault ........................................... 121, 124 Option Unit Fault ............................................................ 125 Oscillation or Hunting....................................................... 137 Output Current ............................................................... 181 Output Current (A) .................................................... 163, 164 Output Frequency............................................................ 181 Output Frequency is not as High as Frequency Reference.............
137 Output Terminal Status ..................................................... 181 Output Voltage Reference .................................................. 181 Overcurrent ............................................................. 121, 124 Overexcitation Deceleration Gain ................................... 125, 180 Overheat 1 (Heatsink Overheat) ........................................... 125 Overload Tolerance.................................................... 163, 164 Overtorque 1............................................................ 122, 130 Overtorque Detection 1 ...............................................
121, 126 Overvoltage....................................................... 121, 122, 126 S Safety Hazard Definitions ....................................................11 Safety Information.............................................................11 S-Curve Characteristic at Accel End...................................... 172 S-Curve Characteristic at Accel Start ..................................... 172 S-Curve Characteristic at Decel End...................................... 172 S-Curve Characteristic at Decel Start ..................................... 172 S-Curve Characteristics.....................................................
120 SE ........................................................................ 122, 131 Serial Communication Reference Selection.............................. 175 Serial Communication Transmission Error ........................ 122, 129 Setup Mode................................................................ 58, 60 Shielded Twisted-Pair Cables................................................43 Side-by-Side Setup ............................................................27 Sinking/Sourcing Mode Switch..............................................21 Slip Compensation Gain ....................................................
172 Slip Compensation Primary Delay Time ................................. 172 Soft Charge Circuit Fault ................................................... 121 Soft CLA Selection.......................................................... 179 Software No. (Flash) ........................................................ 182 Software No. (ROM)........................................................ 182 Speed Agreement Detection Level ........................................ 178 Speed Search ................................................................. 176 Stall Prevention ..............................................................
120 Stall Prevention During Deceleration.................................47, 126 Stall Prevention Level during Acceleration .............................. 178 Stall Prevention Level during Run ........................................ 178 Stall Prevention Selection during Acceleration.......................... 178 Stall Prevention Selection during Deceleration.......................... 178 Stall Prevention Selection during Run .................................... 178 Standard Connection Diagram ...............................................32 STOP Key Function Selection ............................................. 180 Stopping Method After Communication Error ..........................
177 P Parameter Range Setting Error............................................. 132 Parameter Setting Range Error............................................. 122 Parameter Settings.............................................................59 PASS .................................................................... 122, 130 Password 1.................................................................... 171 Password 2.................................................................... 171 Password Settings..............................................................66 Peak Hold Current ...........................................................
182 Performance Life ............................................................ 144 Peripheral Devices Affected by Drive Operation ....................... 138 PF ........................................................................ 121, 127 226 SIEP C710606 33A OYMC AC Drive – J1000 User Manual