ebm-papst · K3G355-PJ75-33 · 5 pp.
ebm-papst K3G355-PJ75-33 EC Centrifugal Fan Data Sheet & Manual PDF
Related manuals
Document text
ebm-papst Mulfingen GmbH & Co. KG Bachmьhle 2 · D-74673 Mulfingen Phone +49 7938 81-0 Fax +49 7938 81-110 info1@de.ebmpapst.com www.ebmpapst.com Limited partnership · Headquarters Mulfingen Amtsgericht (court of registration) Stuttgart · HRA 590344 General partner Elektrobau Mulfingen GmbH · Headquarters Mulfingen Amtsgericht (court of registration) Stuttgart · HRB 590142 Nominal data Type K3G355-PJ75-33 Motor M3G112-EA Phase 3~ Nominal voltage VAC 400 Nominal voltage range VAC 380 .. 480 Frequency Hz 50/60 Method of obtaining data ml Speed (rpm) min -1 2400 Power consumption W 1100 Current draw A 1.7 Min. ambient temperature °C -25 Max. ambient temperature °C 60 ml = Max. load · me = Max.
efficiency · fa = Free air · cs = Customer specification · ce = Customer equipment Subject to change Data according to Commission Regulation (EU) 327/2011 (EN 17166) Actual Req. 2015 01 Overall efficiency η es % 69.2 51.9 02 Measurement category A 09 Power consumption P ed kW 1.09 09 Air flow q v mі/h 3655 03 Efficiency category Static 09 Pressure increase p fs Pa 692 04 Efficiency grade N 79.3 62 05 Variable speed drive Yes 10 Speed (rpm) n min -1 2405 11 Specific ratio * 1.01 Data obtained at optimum efficiency level. The ErP data is determined using a motor-impeller combination in a standardized measurement setup.
* Specific ratio = 1 + p fs / 100 000 Pa LU-174053 ebm-papst Mulfingen GmbH & Co. KG · Bachmьhle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · info1@de.ebmpapst.com · www.ebmpapst.com K3G355-PJ75-33 EC centrifugal module - RadiPac backward-curved, single-intake with support bracket Item no. 56923-5-9980 · ENU · Change 218317 · Approved 2020-08-28 · Page 1 / 5
Technical description Weight 18 kg Size 355 mm Motor size 112 Rotor surface Painted black Terminal box material PP plastic Electronics housing material Die-cast aluminum, painted black Impeller material Sheet aluminum, painted black Support plate material Sheet steel, galvanized and painted black Support bracket material Steel, painted black Inlet nozzle material Sheet steel, galvanized and painted black Number of blades 5 Direction of rotation Clockwise, viewed toward rotor Degree of protection IP55 Insulation class "F" Moisture (F) / Environmental (H) protection class H2+S Max. permitted ambient temp. for motor (transport/storage) +80 °C Min. permitted ambient temp.
for motor (transport/storage) -40 °C Installation position See product drawing Condensation drainage holes On rotor side Mode S1 Motor bearing Ball bearing; (sealed) Technical features - Output 10 VDC, max. 10 mA - Operation and alarm display - External 24 V input (parameter setting) - Alarm relay - Integrated PID controller - Motor current limitation - PFC, passive - RS-485 MODBUS-RTU - Soft start - EEPROM write cycles:
100,000 maximum - Control input 0-10 VDC / PWM - Control interface with SELV potential safely disconnected from the mains - Thermal overload protection for electronics/motor - Line undervoltage / phase failure detection EMC immunity to interference According to EN 61000-6-2 (industrial environment) EMC interference emission According to EN 61000-6-3 (household environment), except EN 61000-3-2 for professionally used equipment with a total rated power greater than 1 kW Touch current according to IEC 60990 (measuring circuit Fig.
4, TN system) Electrical hookup Terminal box Motor protection Thermal overload protector (TOP) internally connected Protection class I (with customer connection of protective earth) Conformity with standards EN 61800-5-1; CE Approval CSA C22.2 No. 77 + CAN/CSA-E60730-1; EAC; UL 1004-7 + 60730-1 ebm-papst Mulfingen GmbH & Co. KG · Bachmьhle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · info1@de.ebmpapst.com · www.ebmpapst.com K3G355-PJ75-33 EC centrifugal module - RadiPac backward-curved, single-intake with support bracket Item no. 56923-5-9980 · ENU · Change 218317 · Approved 2020-08-28 · Page 2 / 5
Product drawing 1 Installed position: shaft horizontal (install support struts only vertically as illustrated) or rotor on bottom; rotor on top on request 2 Cable diameter min. 8 mm, max. 12 mm, tightening torque 1.8±0.3 Nm (use must be made of seal provided) Cable diameter min. 4 mm, max. 10 mm, tightening torque 1.8±0.3 Nm 3 Cable diameter min. 6 mm, max. 10 mm, tightening torque 1.8±0.3 Nm (use must be made of seal provided) Cable diameter min. 4 mm, max. 7 mm, tightening torque 1.8±0.3 Nm 4 Tightening torque 3.5 ± 0.5 Nm 5 Inlet ring with pressure tap (k-factor: 148) 6 Attachment for inlet ring and FlowGrid (00400-2-2957 not included in scope of delivery) ebm-papst Mulfingen GmbH & Co.
KG · Bachmьhle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · info1@de.ebmpapst.com · www.ebmpapst.com K3G355-PJ75-33 EC centrifugal module - RadiPac backward-curved, single-intake with support bracket Item no. 56923-5-9980 · ENU · Change 218317 · Approved 2020-08-28 · Page 3 / 5
Connection diagram No. Conn. Designation Function/assignment 1 PE Protective earth 2 PE Protective earth 3 L1 Power supply 4 L2 Power supply 5 L3 Power supply 6 NC Status relay, floating status contact, break for failure, contact rating 250 VAC / 2 A (AC1) / min. 10 mA; reinforced insulation on supply side and basic insulation on control interface side 7 COM Status relay, floating status contact, break for failure, contact rating 250 VAC / 2 A (AC1) / min.
10 mA; reinforced insulation on supply side and basic insulation on control interface side 8 GND Reference ground for control interface, SELV 9 RSA RS485 interface for MODBUS, RSA; SELV 10 RSB RS485 interface for MODBUS, RSB; SELV 11 0-10 V Analog input (set value) SELV, 0-10 V, Ri = 100 kΩ, adjustable curve 12 +10 V Fixed voltage output 10 VDC, SELV, +10 V ±3%, max. 10 mA, short-circuit-proof, power supply for external devices (e.g. pot); fixed voltage input 24 VDC for setting parameters via MODBUS without line voltage supply ebm-papst Mulfingen GmbH & Co.
KG · Bachmьhle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · info1@de.ebmpapst.com · www.ebmpapst.com K3G355-PJ75-33 EC centrifugal module - RadiPac backward-curved, single-intake with support bracket Item no. 56923-5-9980 · ENU · Change 218317 · Approved 2020-08-28 · Page 4 / 5