Руководство по ремонту Toyota Land Cruiser J100 - настройка дверей (EN)

REMOVAL

Last Modified: 6-7-2017 6.8:8.0.40 Doc ID: RM000001BLF000X agn Model Year Start: 2006 Model: Land Cruiser Prod Date Range: [05/2005 - ] Title: ENGINE HOOD / DOOR: BACK DOOR: ADJUSTMENT; 2006 MY Land Cruiser [05/2005 - ] ADJUSTMENT 1. ADJUST DOOR IN LEFT/RIGHT AND VERTICAL DIRECTIONS (a) Loosen the door's hinge bolts and adjust the door's position. (b) Tighten the door's hinge bolts after the adjustment. Torque: 28 N·m {286 kgf·cm, 21ft·lbf} 2. REMOVE DOOR IN FORWARD/REARWARD AND VERTICAL DIRECTIONS (a) Loosen the door's hinge nuts and adjust the door's position. (b) Tighten the door's hinge nuts after the adjustment. Torque: 31 N·m {316 kgf·cm, 23ft·lbf} 3.

ADJUST BACK DOOR LOCK STRIKER (a) Check that the door fit and door linkages are adjusted correctly. (b) Using a "torx" wrench, loosen the door lock striker mounting screws. "Torx" wrench: T40 (Part No. 09042-00020 or locally manufactured tool) Torque: 11.5 N·m {117 kgf·cm, 8ft·lbf} (c) Using a plastic-faced hammer, tap the door lock striker to adjust. 4. ADJUST LOWER STOPPER (a) Loosen the stopper mounting bolt to adjust. (b) Use the same manner described above to the side. 5. REMOVE DOOR IN FORWARD/REARWARD AND VERTICAL DIRECTIONS (a) Loosen the door's hinge bolts and adjust the door's position. (b) Tighten the door's hinge bolts after the adjustment. Torque:

28 N·m {286 kgf·cm, 21ft·lbf} 6. ADJUST DOOR IN LEFT/RIGHT AND VERTICAL DIRECTIONS (a) Loosen the door's hinge bolts and nut to adjust the door's position. (b) Tighten the door's hinge bolts and nuts to after the adjustment. Torque: 31 N·m {316 kgf·cm, 23ft·lbf} cardi

Стр. 1

REMOVAL

cardiagn.com 7. ADJUST DOOR LOCK STRIKER (a) Check that the door fit and door linkages are adjusted correctly. (b) Using a "torx" wrench, loosen the door lock striker mounting screws. "Torx" wrench: T40 (Part No. 09042-00020 or locally manufactured tool) Torque: 11.5 N·m {117 kgf·cm, 8ft·lbf} (c) Using a plastic-faced hammer, tap the door lock striker to adjust.

Стр. 2

REMOVAL

Last Modified: 6-7-2017 6.8:8.0.40 Doc ID: RM000001BLG000X agn Model Year Start: 2006 Model: Land Cruiser Prod Date Range: [05/2005 - ] Title: ENGINE HOOD / DOOR: BACK DOOR: COMPONENTS; 2006 MY Land Cruiser [05/2005 - ] COMPONENTS ILLUSTRATION ILLUSTRATION cardi

Стр. 3

REMOVAL

Last Modified: 6-7-2017 6.8:8.0.40 Doc ID: RM000001BLH000X agn Model Year Start: 2006 Model: Land Cruiser Prod Date Range: [05/2005 - ] Title: ENGINE HOOD / DOOR: BACK DOOR: DISASSEMBLY; 2006 MY Land Cruiser [05/2005 - ] DISASSEMBLY 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL CAUTION: Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag activation. 2. REMOVE ASSIST GRIP (a) Using a screwdriver, remove the 2 assist grip plugs. HINT: Tape the screwdriver tip before use. (b) Remove the 2 screws and assist grip. 3. REMOVE BACK DOOR INSIDE HANDLE BEZEL 4.

REMOVE CENTER BACK DOOR GARNISH (a) Using a screwdriver, remove the center back door garnish. HINT: Tape the screwdriver tip before use. 5. REMOVE BACK DOOR GARNISH (a) Using a screwdriver, remove the center back door garnish. HINT: Tape the screwdriver tip before use. 6. REMOVE REAR WIPER ARM (a) Open the cover. (b) Remove the nut and rear wiper arm. Torque: 5.4 N·m {55 kgf·cm, 48in·lbf} (c) Remove the grommet. 7. REMOVE REAR WIPER MOTOR AND LINK ASSEMBLY (a) Disconnect the connector. (b) Remove the 2 bolts. (c) Unfasten the 3 bolts and remove the rear wiper motor and link assembly. cardi

Стр. 7