SYSTEM OUTLINE When the ignition SW turned on, the current from the WIPER fuse flows to the front wiper and washer SW TERMINAL 17, and front wiper motor TERMINAL 2. 1. LOW POSITION When the wiper SW is turned to LO position, the current flows from the front wiper and washer SW TERMINAL 17 to TERMINAL 7 to front wiper motor TERMINAL 1 to TERMINAL 5 to GROUND, and operates the front wiper motor at low speed. 2. HIGH POSITION When the wiper SW is turned to HI position, the current flows from the front wiper and washer SW TERMINAL 17 to TERMINAL 8 to front wiper motor TERMINAL 4 to TERMINAL 5 to GROUND, and operates the front wiper motor at high speed. 3.
INT POSITION When the wiper SW is turned to INT position, the relay operates and the current which is connected by the relay function flows from the front wiper and washer SW TERMINAL 17 to TERMINAL 2 to GROUND, and operates the wipe. The intermittent operation is controlled by the charge/discharge function of the condenser installed in the relay, and the intermittent time is controlled by a time control SW to change the charging time of the condenser. 4.
WASHER CONTINUOUS OPERATION When the washer SW is turned on, the current flows from the washer motor TERMINAL 2 to TERMINAL 5 to front wiper and washer SW TERMINAL 11 to TERMINAL 2 to GROUND, operates the washer motor and the window washer emits a water spray. This causes the current to flow to the washer continuous operation circuit in front wiper and washer SW TERMINAL 11 to TERMINAL 7 to front wiper motor TERMINAL 1 to TERMINAL 5 to GROUND, and operates the wiper. : PARTS LOCATION : JUNCTION BLOCK AND WIRE HARNESS CONNECTOR : CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS 147 SERVICE HINTS C21 FRONT WIPER AND WASHER SW [COMB. SW] 2–GROUND : Always continuity 17–GROUND : Approx.
12 volts with ignition SW at ON or ST position 7–GROUND : Approx. 12 volts with front wiper and washer SW at LO position : Approx. 12 volts 1.6 to 10.7 seconds intermittently with the front wiper and washer SW at INT position 16–GROUND : Approx. 12 volts with ignition SW on unless the front wiper motor at STOP position 8–GROUND : Approx. 12 volts with front wiper and washer SW at HI position F6 FRONT WIPER MOTOR 2–3 :
Closed unless the wiper motor at STOP position SERVICE HINTS Code See Page Code See Page Code See Page C21 40 J20 41 W1 39 F6 38 J24 41 Code See Page Junction Block and Wire Harness (Connector Location) 1A 23 Engine Room No.2 Wire and Engine Room J/B (Engine Compartment Left) 1H 23 Engine Room Main Wire and Engine Room J/B (Engine Compartment Left) 2F 26 Engine Room No.2 Wire and Cowl Side J/B LH (Left Kick Panel) 2P 28 Instrument Panel Integration Wire and Cowl Side J/B LH (Left Kick Panel) 3A 32 Engine Room No.2 Wire and Cowl Side J/B RH (Right Kick Panel) 3I 32 Instrument Panel Integration Wire and Cowl Side J/B RH (Right Kick Panel) Code See Page Joining Wire Harness and Wire Harness (Connector Location) IG2 50 Engine Room No.2 Wire and Dash Wire (Behind the Combination Meter) IH1 50 Instrument Panel Integration Wire and Column Wire (Near the Ignition SW) IH2 II2 50 Column Wire and Dash Wire (Near the Ignition SW) IW1 54 Engine Room No.2 Wire and Dash Wire (Behind the Glove Box)