FLENDER Standard Couplings Flexible Couplings — N-EUPEX and N-EUPEX DS Series © Siemens AG 2015 Type H 7 During assembly, the gap dimension S2 must not exceed the permissible tolerance of +1 mm. The hub diameter of the component part is assigned according to the diameter of the finished bore. Where bore diameters over- lap, the component with the smaller hub diameter is always se- lected. Weights and mass moments of inertia apply to maximum bore diameters. Ordering example: N-EUPEX H coupling, size 160, S = 200 mm, Part 1: Bore D1 60H7 mm, keyway to DIN 6885-1 and set screw, Part 2: Bore D2 55H7 mm, keyway to DIN 6885-1 and set screw. Article No.:
2LC0100-7AG99-0AD0 L1E+M1D The article number applies to standard flexibles of 80 ShoreA; the article number for alternative flexible types is available on request. 7/13 Siemens MD 10.1 · 2015 Size Rated torque flexible type 80 ShoreA Speed Dimensions in mm Mass moment of inertia Article No. Weight Bore with keyway to DIN 6885 Order codes for bore diameters and tolerances are specified in catalog section 3 TKN nKmax D1 D2 DA ND1 ND2 NL1 NL2 S2 S LZ DZ LG J1 J2 m min. max. min. max.
Nm rpm kgm2 kgm2 kg 200 1340 3400 – 85 – 85 200 140 140 80 90 6 140 118.5 144 310 180 158.5 350 200 178.5 370 250 228.5 420 0.04 0.095 2LC0101-0AG ■ ■ -0AB0 25.6 0.1 2LC0101-0AG ■ ■ -0AC0 26.5 0.105 2LC0101-0AG ■ ■ -0AD0 27.2 0.11 2LC0101-0AG ■ ■ -0AE0 28.5 225 2000 3000 – 90 – 90 225 150 150 90 100 6 140 118.5 169 330 180 158.5 370 200 178.5 390 250 228.5 440 0.07 0.158 2LC0101-1AG ■ ■ -0AB0 34 0.16 2LC0101-1AG ■ ■ -0AC0 35 0.17 2LC0101-1AG ■ ■ -0AD0 36 0.18 2LC0101-1AG ■ ■ -0AE0 38 250 2800 2750 46 100 46 100 250 165 165 100 110 8 180 152.5 185 390 200 172.5 410 250 222.5 460 0.12 0.27 2LC0101-2AG ■ ■ -0AC0 48 0.28 2LC0101-2AG ■ ■ -0AD0 50 0.3 2LC0101-2AG ■ ■ -0AE0 52 280 3900 2450 49 110 51 110 280 180 180 110 120 8 250 222.5 215 480 0.20 0.52 2LC0101-3AG ■ ■ -0AE0 70 315 5500 2150 49 100 51 120 315 165 200 125 140 8 250 222.5 250 515 90 120 200 0.32 0.87 2LC0101-4AG ■ ■ -0AE0 98 0.35 2LC0101-4AG ■ ■ -0AE0 100 350 7700 2000 61 110 51 140 350 180 230 140 150 8 250 220.5 272 540 90 140 230 0.54 1.4 2LC0101-5AG ■ ■ -0AE0 120 0.61 2LC0101-5AG ■ ■ -0AE0 125 400 10300 1700 66 120 51 150 400 200 250 160 180 8 250 185.5 310 590 100 150 250 1.0 2.9 2LC0101-6AG ■ ■ -0AE0 195 1.1 2LC0101-6AG ■ ■ -0AE0 200 440 13500 1550 80 130 51 160 440 215 265 180 180 10 250 182 354 610 120 160 265 1.5 4.1 2LC0101-7AG ■ ■ -0AE0 225 1.7 2LC0101-7AG ■ ■ -0AE0 230 ∅D1:
• Without finished bore – Without order codes 1 • Without finished bore sizes 315 to 440 for 2nd diameter range D1 – Without order codes 2 • With finished bore – With order codes for diameter and tolerance (article number without "-Z") 9 ∅D2: • Without finished bore – Without order codes 1 • Without finished bore sizes 315 to 440 for 2nd diameter range D2 – Without order codes 2 • With finished bore – With order codes for diameter and tolerance (article number without "-Z") 9