MIL-STD MIL-STD-810B Method 513.1 / 514.1 — MIL-STD-810B Method 513.1 Acceleration & 514.1 Vibration Test Standard PDF

., .. . .,. . ...= Downloaded from https://www.everyspec.com ,-. ~,,. 15 June 196’f ., .... Contaminant ion i;n:rols. - Con:ardnationlevels shall be controlledand . measufed T,Oinsure that emissivity end abs”tirbtive values are not altered by more-” th~ 5X Of the iqit$d v+lues.of the flight Or test h?rdw~e from-time Of ‘CePtmce of test article to completion of the test. Mxbslidloi+ ~. 2,.4 ! . . . 3, Prep&ration,fortee.t.- _. .. . . 3,1 Informationreaulred. - In preparingthe specimen for a test, typical informationreQuired,ia: . . . (a) Need””forsimulatingp18nei/moonradiation and albedo. (b) Rotational modes and attitude orientation, as e,pplicable.

- (c) Programming s o l a r rad~ation in accordance with the miseion (considering tpe day @ night ~rbitfng perf?de Plus cfsl~~ - end tra.niiunamissions). (d) (e) (f) (g) (h) (i) (J) Equipment operatio:,duty cycles. &ration of test. Method for monitoring test item during teet. Operating parameters to be monitored. Allowable deviation from specifiedtolerances. Coupling of radio frequency outpute to dummy loads. Substitution of power source having volt-ampere characteristics similarto. the vehicle’s primY’ Power SUPPIY. Finissionof fuels and oxidizers. Stetement of reliability and failure criteria.

Peripheral heating and cooling devices to maintain proper conditions of equipment under test until flight conditions are established. Aerodynamic heating simulationrequirement. Vehicle surface emissivity and absorptivity. Vehicle thermal balance computations. Minimum heating conditions (i.e., the coldest condition which is often the most difficultto achieve). Auxiliary power to supplementpower equipment for chamber (k) (1) (m) ,/--- (n) (C! (p) (q) ., , (r) (s) and equipment under test. Other applicablerequirements. 3.2 Simulatorperformancep=ameter validation.- I’heinstrumentperformance ch=t, table517.1-V,indicatesthe levelOf perfO=ce requiredOf inatr~entsfOr indicated parmneters:

absolute accuracy, reproducibility,response time, view angle, discriminate ion or senaitivity, and miscellaneousitems for the evaluation o f s o l a r simulation. ,. 3.3 Teet duration, - When the intendedmission time of the test item i= such that the test item will be exposed to low pressure conditions for periods in excess of 24 hours,the test chambershallbe maintainedat a pressureof at least1 X 10-5 Torr fornot lessthan 24 hoursto properly’validatethe perfom.anteof thetest item. Teet itemwith intendedflighttimes of lessthan Zk hoursshallbe exposedto lW pressurefor a time equal to or longerthapthe actualintendedflighttimeto proper- ly validatethe perfo-ce of the test item. ...

517.1-5 M?lMOD517.1 -- 20 October1969 .: ,.- ,., . .. . -.::,. . .,7..- .Y : ..,., .,’,, .. .. . . . ... .—.=,... . . ,.7----- ....... .,..., .-::”.-.7: =y~ ~:-,; -~:. .,...,.,:.‘..-. ;?.:.= “=::;:,: “-”-:.;:>7’;7.-’ ~-:=”%..:.,. .-;~,x7-==-- ... .... ......-’.. .. .. .. .....-,.,....... . .,.:. .,:.,. ....., .,.,,,.. , -.:,. ..,: ., .. ..,,::~:,.:::y..:..”; .:,:-:- .,.,, .,y.,,,-:.:,. ;:-:;,;$.! .:.:.!.;: :*; .:; ,: .... ,), . .,. .,: .’., ,, ’::,.. ..: :., ,,, ...... c