MIL-STD MIL-STD-810B Method 513.1 / 514.1 — MIL-STD-810B Method 513.1 Acceleration & 514.1 Vibration Test Standard PDF

.. . Downloaded from https://www.everyspec.com .,. ,.- MIL-STD-81OB “’””” . 15 June 1967 ; compliance with 2,2,1 of this method shall then be applied to the test item. normal rotational mode of the test item along with otherrequirements~d cOndltiOns shall then be established and maintainedthroughout the test. Measurementsmade during the test shall be compared with the data obtained in accordancewith General Requirements, Section 3, paragraph3.2.1. At the conclusionof the test,thetest chamber shall be returned to Btmdard ambientconditionsand stabilizedand the tent item inspectedin accordancewith GeneralRewire~nt~, Section3t Paragraph3.2.4.

., k.2 Procedure II - Heat flux simulation.- The test object shall be located vithin the test chamber (apparatus 2.1) having a cryogenic heat sink (apparatus2.3). A heat flux simulation source (apparatus2.2.2) shallbe providedsurroundingthe test objectand thermallyieolatedfromit. The test objectshallbe supportedby low heat conduction m.eanE, The teat shall be ~erformed ae described in 4.1.1. 4,3 Procedure III - Heat-fl:v thermal canister.- T%e test object shall be located within the test :hamber (apparatus 2,1) having a cryogenic heat sink (appamtus 2.3) with a thermez ~t~nister(appwatus 2.~.1). The teat object shall be mounted within the canister ty low heat conductionmeans.

The test shall be performed as describedin h.1.1. 4,4 Procedure IV-- Heat flux sirmiition”variable temDerature shroud. - The teat object shall be located within the test ch~ber (apparatuS 2.1).havinsa variable temperature shroud (apparatus2.4.2). The tent objeot mhall be mounted within the shroudby low heat conductionmeann. Lol,l, The tent shall be perfomed u describedin . ....> k.5 ProcedureV - Heat fluxwithconductivesourceand crycv?enic shroud.- The ,, +.estobjectshallbe locatedwithinthe test chauber(apparatus2.1)havinga cryO- genicheat sink (apparatus2.3). / The test ob.1 ect shallhave a conductivesource (~ppa.@:~ p ~) attachedto it ~d ~~1 be supported ~ low heat conductionmeans.

4.6 procedure VI - Vacuum simulation.- The test ob~ect shall be located within $,hetest chamber, (apparatus2.1). Its volume should be ‘preferablymuch smaller than chamber volume. All test fixtures should be vacuum compatible. lt.’7fiOcedure ~ - Heat flux ti18tion @th vehicle heaters. - The test object shall be located within the test chamber (aPWr~tus 2.1) hti% .9cryogdc heat S~ (apparatus 2.3). ‘The teSt object shall have vehcle heaters (heaterbmet~ ., fl~d .s@em) attached to its surface. 5. Definitions.- Terms frequentlyused fi solar stilation in conjunctionwith thermal vacuum t,estkngare as follows:

(a) Absoitiance.-Absorptanceie the ratioof the abeorbedradiantflux to the iicidentradi~t flwi. Totalab,aorptarice refereto absorptance measuredover all wavele@”ha. Spectralabsorptancerefersto absorp. tancemeasuredat a s cified wavelength. (b) -. - r Albedo is t e ratio of the amount of electroma@etic.radiation reflected by a body to the amount”incident upon it. This fraction is often expressed as a percentage, such as 34 percent for earth a.lbedo. The spectrum of reflectedenergy.is’generally clifferent from that of the ,.. incident radiation.~. :~~- --- .: ..’ :>::-f:.: ~ .. ,. ,. .,, .->. I I .,. ,.. : , ~..’ ,.___ . .. .,