16 pp.

tima011.tmp

Document text

F , , 3 Downloaded from https://www.everyspec.com IIIIL-STD-8 10C NOTICE 1 7 April 198j - / ,.. * 141LIT4RY STANDARD ..... I - ;l; , EN,VIdONHWTAL ... :.,: , . TEST METHODS TO ALL HOLDERS OF HIL.%D-81OC: 1. THE FOLLOUING TEST METHOD HAS BEEN REVISED AND SUPERSEDES THE TEST ~THOD LISTED: Nwm#yiQ. Rats ~. Rats . 7 Aw1l 1981 . 10 PIerch1975 2. RETAIN THIS NOTICE AND INSERT BEFORE TABLE OF CONTENTS, 3. Holders of KIL-STD-81OC will verify that the supersedure indicated above haa been entered. This notice page will be retained as a check sheet. This issuance la a separate publication. Each notice la to be retained b~ stocking points until the liilitary Standard is Cmpletely retiaed or canceled.

Cmtodiane: Aney - ER Navy - AS Air Force - 11 Preparing activity: Air Force - 11 Project No. MISC-0C73. Fsc “Msc ., . . .

Page 1

1 . . Downloaded from https://www.everyspec.com . . MIL-SID-810C 10 krch 1975 METNOD 508.2 FUNGUS Section I 1.1 llQEX Section 1 1.1 508.2-1 508.2-1 508.2-1 Index . . . . . . . . . . . . . . . . . . .. . . . . Purpose . . . . . . . . . . . . . . . . . . . . . . Environmental effeOtS . . . . .. . . . . ... . . :.: Guidelines for deterudnlng test ::; Proceduresand teat conditions . . . . . . . . . Special considerations . . . . . . . . . . . . . . References . . . . . . . . . . . . . . . . . . . . 1.4 1.5 1.6 508.2-3 508.2-4 508.2-5 Section II Apparatus. . . . . . . . . . . . . . . . . . . . . Preparation for test... . . . . . . . . . . . . Procedures . . . . . . . . . . . . . . . . . . . .

Information to be recorded . . . . . . . . . . . . II.1 11.2 11.3 11.4 508.2-8 508.2-8 508.2-9 508.2-15 1.2 f’JJRPOS&.The purpose of the fungus chamber test la to assess the extent to which the test item will support fungal growth and how the fungal growth MY affect performance or use of the test item. 1.3 ~. Fungal growth impaira the fU!WtiOniIIgor !JSeof equipment by changing the physical properties of the equlpuent. 1.3.1 ~ mchaw. e The damage mecheniems =e as follows: a. Direct.attack on materiale. Non-reslatant materials are auaceptfble to direct attack as the fungi break the material do= and uae it as food. This results in deteriorationaffecting the physical properties of the material.

Examples of non-resistantmateriala are: (1) Natural materials - (Products of natural origin are most swceptible to this attack) - Celluloeic materials (e.g. mod, paper, natw~ fiber textiles and cordag~f). (b) Animal and vegetable baaed edheaivea. (c) Greaae, olla and many hydrocarbon. (d) Leather. ME~ 508.2 7 Airil 1981 508.2-1

Page 2

HIL-STD-81Oc Downloaded from https://www.everyspec.com . . . ., I (2) Synthetic materials - (a) PVC formulations esters). (e.g. those plasticized with fatty acid 1. (b) Certain polyurethames (e.g. polyesters and some polyethers). (c) Plastics, ~ich contain organic fillers of laminatingmateriala. (d) Paints and varnishes which contain susceptible constituents. b. Indirect attack on materials. Damage to fungus resistant !aeterialsresults from indirect attack when:

(1) fungal growth on surface deposits of dust, grease, perspiration and other contaminants which find their way onto equipment during manufacture or accumulate during service can cause damage to the underlying material even though that materiel may be resistant to direct attack. (2) metabolic waate products (i.e. organic acids), excreted by fwzi, cause corrosion of metals, etching of glass or staining or degradi~ of plastics and other materiale. (3) the products of fungal growth on adjacent materials, which are susceptible to direct attack, come in contact with th+ resistant @terlals. X.3.2 Phvsical interferemce. Physical Interference can occur as follows: a.

Electrical or electronic systems. Damage to electrical or electronic systems may result from either direct or indirect attack. Fungal growth can form undesirable electrical conducting paths across insulating materials or may adversely affect the electrical characteristics of critically adjusted electronic circuits. b. Optical systems. Damage to optical systems results primarily from indirect attack. The fungal growth can adversely affect light transmiaaion through the optical system; block dellcate moving parts; and change non-wetting surfaces to wetting surfaces with resulting loss in performance. I I i. 1.3.3 ~. *US gro~h on equi~ent CSM cause physiological problems, (e.g.

allergies) or be so aesthetically W@easant that the users will be reluctant to use the equipment. 1.4 FOR ~S. Since microbial deterioration is a function of temperature end humidity and la en Inseparable condition of bet-humid tropics and the midlatitudes, it must be considered in the design of all standard general purpose materiel.1 Method 508.2 (Fungus) consequently Is used when an item is to be tested to determine if fungus growth will occur and if SO, how it will affect the use of the item. lFra AR 70-38, Research, pavelopment, Test and Evaluation of Material for Extreme Climatic Caditlons, Chapter 2, Climatic Criteria. / METHOD 508.2 508.2-2

Page 3

Downloaded from https://www.everyspec.com ‘ MIL-STD-81OC .! a . oD t i on s . The orMons are limited ‘~rfo-ming a functional test prior to to extending the teet duration and amd following the fungue test. b. The related test conditions involve primarily: (1) Test time”(28 to 8Q days). (2) Test configuration - whether the test Item shall be exposed in other than an unsealed condition. 1.4.1 ~ a. The operational purpose of the test item. From the require?nenta,determine the functions to be performed by the equipment and any 1imit1% conditions, (e.g. storage, human factors aepacts, whether it is a large volumellow coat/ expendable item, etc .). b. Required test data.

The prImary questions that may be addressed after the fungu9 test are: Will fungue grow on the item? (1) (2) How rapidly will it grow on the teet item? (~) How does the fungue growth affect the test item? (4) To what extent will the fungus affect the mission of the item? (5) Can the test item be atorad effectively in a field environment? Is the test item Bafe for use following fungal growth? (6) (7) Are there simple reversal processes, e.g. wiping off fungal growth? c. Selection of test phasea. Three test phasee are included within Uethod 508.2 (pre-test, chamber and performance). Based on the test requir~ente document, determine which phases are applicable.

(1) Phase I (we-test) - Phaee I la conducted in all caaes to provide baseline data. (2) Phase 11 (chamber) - Phase II 1s the basic fungus test and is conducted in all cases. (3) Phase III (Parfomance) - Phaae III is used to determine compliance with the performance requirements of the test item following the fungus chamber test. 1 . 4 . 2 ~ . Recognizing that at least two of the test phases must be conducted, the mimery decisions must be made concerning teat duration and test item configuration. 508.2-3 UETHOD508.2

Page 4