M800/M80/E80 Series Alarm/Parameter Manual

Introduction This manual is a guide for using the Mitsubishi Electric CNC. Supported models are as follows: Abbreviations in this manual are as follows: Be sure to keep this manual always at hand. Notes on Reading This Manual (1) This manual explains general parameters as viewed from the NC. For information about each machine tool, refer to manuals issued from the machine manufacturer. If the descriptions relating to "restrictions" and "allowable conditions" conflict between this manual and the machine manu- facturer's instruction manual, the later has priority over the former. (2) This manual is intended to contain as much descriptions as possible even about special operations.

The operations to which no reference is made in this manual should be considered impossible. CAUTION For items described as "Restrictions" or "Usable State" in this manual, the instruction manual issued by the machine tool builder takes precedence over this manual. Items not described in this manual must be interpreted as "not possible". This manual is written on the assumption that all the applicable functions are included. Some of them, however, may not be available for your NC system. Refer to the specifications issued by the machine tool builder before use. Refer to the Instruction Manual issued by each machine tool builder for details on each machine tool.

Some screens and functions may differ depending on the NC system (or its version), and some functions may not be pos- sible. Please confirm the specifications before use. To protect the availability, integrity and confidentiality of the NC system against cyber-attacks including unauthorized ac- cess, denial-of-service (DoS) (*1) attack, and computer virus from external sources via a network, take security measures such as firewall, VPN, and anti-virus software. (*1) Denial-of-service (DoS) refers to a type of cyber-attack that disrupts services by overloading the system or by exploiting a vulnerability of the system.

Mitsubishi Electric assumes no responsibility for any problems caused to the NC system by any type of cyber-attacks in- cluding DoS attack, unauthorized access and computer virus. In this manual, the following abbreviations might be used. L system: Lathe system M system: Machining center system MTB: Machine tool builder Also refer to the manuals on "Manual List" as necessary.

Supported models Abbreviations in this manual M800W Series M850W, M830W M800S Series M850S, M830S M80W Series M80W M80 Series M80 TypeA, M80 TypeB E80 Series E80 TypeA, E80 TypeB Abbreviations Supported models M800, M800 Series M800W Series/M800S Series M80, M80 Series M80W Series/M80 Series M800/M80, M800/M80 Series M800W Series/M800S Series/M80W Series/M80 Series M8, M8 Series M800W Series/M800S Series/M80W Series/M80 Series/E80 Series

Стр. 2

Manual List Manuals related to M800/M80/E80/C80 Series are listed as follows. These manuals are written on the assumption that all optional functions are added to the targeted model. Some functions or screens may not be available depending on the machine or specifications set by MTB. (Confirm the specifications before use.) The manuals issued by MTB take precedence over these manuals. Manual IB No. Purpose and Contents M800/M80/E80 Series Instruction Manual IB-1501274 Operation guide for NC Explanation for screen operation, etc. C80 Series Instruction Manual IB-1501453 Operation guide for NC Explanation for screen operation, etc.

M800/M80/E80/C80 Series Programming Manual (Lathe System) (1/2) IB-1501275 G code programming for lathe system Basic functions, etc. M800/M80/E80/C80 Series Programming Manual (Lathe System) (2/2) IB-1501276 G code programming for lathe system Functions for multi-part system, high-accuracy function, etc. M800/M80/E80/C80 Series Programming Manual (Machining Center System) (1/2) IB-1501277 G code programming for machining center system Basic functions, etc. M800/M80/E80/C80 Series Programming Manual (Machining Center System) (2/2) IB-1501278 G code programming for machining center system Functions for multi-part system, high-accuracy function, etc.

M800/M80/E80 Series Alarm/Parameter Manual IB-1501279 Alarms Parameters C80 Series Alarm/Parameter Manual IB-1501560 Alarms Parameters

Стр. 3

Manuals for MTBs (NC) Manuals for MTBs (drive section) Manual IB No.

Purpose and Contents M800/M80/E80/C80 Series Specifications Manual (Function) IB-1501505 Model selection Outline of various functions M800/M80/E80/C80 Series Specifications Manual (Hardware) IB-1501506 Model selection Specifications of hardware unit M800W/M80W Series Connection and Setup Manual IB-1501268 Detailed specifications of hardware unit Installation, connection, wiring, setup (startup/adjustment) M800S/M80/E80 Series Connection and Setup Manual IB-1501269 Detailed specifications of hardware unit Installation, connection, wiring, setup (startup/adjustment) C80 Series Connection and Setup Manual IB-1501452 Detailed specifications of hardware unit Installation, connection, wiring, setup (startup/adjustment) M800/M80/E80 Series PLC Development Manual IB-1501270 Electrical design I/O relation (assignment, setting, connection), field network Development environment (PLC on-board, peripheral development environment), etc.

M800/M80/E80 Series PLC Programming Manual IB-1501271 Electrical design Sequence programming PLC support functions, etc. M800/M80/E80/C80 Series PLC Interface Manual IB-1501272 Electrical design Interface signals between NC and PLC M800/M80/E80 Series Maintenance Manual IB-1501273 Cleaning and replacement for each unit Other items related to maintenance C80 Series Maintenance Manual IB-1501454 Cleaning and replacement for each unit Other items related to maintenance Manual IB No.

Contents MDS-E/EH Series Specifications Manual IB-1501226 Specifications for power supply regeneration type MDS-E/EH Series Instruction Manual IB-1501229 Instruction for power supply regeneration type MDS-EJ/EJH Series Specifications Manual IB-1501232 Specifications for regenerative resistor type MDS-EJ/EJH Series Instruction Manual IB-1501235 Instruction for regenerative resistor type MDS-EM/EMH Series Specifications Manual IB-1501238 Specifications for multi-hybrid, power supply regeneration type MDS-EM/EMH Series Instruction Manual IB-1501241 Instruction for multi-hybrid, power supply regeneration type DATA BOOK IB-1501252 Specifications of servo drive unit, spindle drive unit, motor, etc.

Стр. 4

Manuals for MTBs (Others) ■ For M800/M80/E80 Series Manual No. Purpose and Contents GOT2000 Series User’s Manual (Hardware) SH-081194 Outline of hardware such as part names, external dimensions, installation, wiring, maintenance, etc. of GOTs GOT2000 Series User’s Manual (Utility) SH-081195 Outline of utilities such as screen display setting, operation method, etc.

of GOTs GOT2000 Series User’s Manual (Monitor) SH-081196 Outline of each monitor function of GOTs GOT2000 Series Connection Manual (Mitsubishi Electric Products) SH-081197 Outline of connection types and connection method between GOT and Mitsubishi Electric connection devices GT Designer3 (GOT2000) Screen Design Manual SH-081220 Outline of screen design method using screen creation software GT Designer3 Manual No.

Purpose and Contents GOT2000/GOT1000 Series CC-Link Communication Unit User's Manual IB-0800351 Explanation for handling CC-Link communication unit (for GOT2000 series/GOT1000 series) GX Developer Version 8 Operating Manual (Startup) SH-080372E Explanation for system configuration, installation, etc.

of PLC development tool GX Developer GX Developer Version 8 Operating Manual SH-080373E Explanation for operations using PLC development tool GX Developer GX Converter Version 1 Operating Manual IB-0800004E Explanation for operations using data conversion tool GX Converter GX Works2 Installation Instructions BCN-P5999-0944 Explanation for the operating environment and installation method of GX Works2 GX Works2 Version 1 Operating Manual (Common) SH-080779ENG Explanation for the system configuration of GX Works2 and the functions common to Simple project and Structured project such as parameter setting, operation method for the online function GX Works2 Version 1 Operating Manual (Simple Project) SH-080780ENG Explanation for methods for such as creating and monitoring programs in Simple project of GX Works2 GX Works2 Version 1 Operating Manual (Simple Project, Function Block) SH-080984ENG Explanation for methods for such as creating function blocks, pasting function blocks to sequence programs, and operating FB library in Simple project of GX Works2 GX Works2 Version 1 Operating Manual (Structured Project) SH-080781ENG Explanation for methods for such as creating and monitoring programs in Structured project of GX Works2 GX Works3 Installation Instructions BCN-P5999-0391 Explanation for the operating environment and installation method of GX Works3 MELSEC-Q CC-Link System Master/ Local Module User’s Manual SH-080394E Explanation for system configuration, installation, wiring, etc.

of master/local modules for CC-Link system GOT2000 Series Connection Manual (Non-Mitsubishi Electric Products 1) SH-081198ENG Explanation for connection types and connection method between GOT and other company's devices GOT2000 Series Connection Manual (Non-Mitsubishi Electric Products 2) SH-081199ENG GOT2000 Series Connection Manual (Microcomputers, MODBUS/ Fieldbus Products, Peripherals) SH-081200ENG Explanation for connection types and connection method between GOT and microcomputers, MODBUS/fieldbus products, peripherals GT SoftGOT2000 Version1 Operating Manual SH-081201ENG Explanation for system configuration, screen configuration and operation method of monitoring software GT SoftGOT2000

Стр. 5