THE NEW MYFORD ML1IO LATHE Bed, box section casting in MEEHANITE ir'on, with "solid" top for extra rigidity. Bed precision ground on top face and angular shears. Headstock spindle hardened and ground. Primary drive belt guard and changewheel guard both provided with backplates for fullest enclosure. Changewheel guard with single point fixing for quick removal. Pivoted headstock drive belt guard also ccvers backgearing. Ouick action belt tension release for headstock drive facilitates speed changing. Rapid clamping of tailstock to bed by lever action. Tailstock with separate base for set-over for taper turning. Leadscrew bearing brackets fitted bronze bushes.

Leadscrew fitted ball handle for fine, manual, saddle feeds. Leadscrew clutch available as additional equipment. Clamping screws fitted to saddle and cross slide. Cross slide provided with 4 tee slots for use as boring table. Top slide arranged to swivel 360". Thread dial indicator fitted as standard. SPECIFICATION Centre height Maximum admitted between centres Width across bed shears (to sharp corners) Headstock spindle nose bored Headstock spindle bored through Spindle nose register Spindle nose thread Swing over saddle Swing over cross slide Cross slide travel Cross slide micrometer Ditto, metric divisions, Top slide base swivels Top slide base graduated180' either side, divisions . .

3*' (84 mm) 13" (330 mm) 3" (76 mm) No.2 M.T. 0.6'(15.24 mm) 1l' dia. (31 .75 mm) 1*' x 12T.P.1. 5+' (149 mm) 3E' (98 mm) 4*' (108 mm) 0.001 " 0'02 mm 360' 10 2'(51 mm) 0.001 ' Top slide travel rop iiioe microreter oiai, oivtlons Ditto, metric divisions .. Height from slide to centre Height from top slade Tailstock barrel bored 0.02 mm +' (12.5 mm) No.2 M.T. 3' (76 mm) Tailstock barrel travel Tailstock set-over, to the froni Tailstock set-over, to the rear Leadscrew Spindle speeds, 1425 R.P.M. Spindle speeds, 1750 R.P.M.

Screwcutting range Screwcutting range, metric (with extra gears) Feeds, per revolution of headstock spindle Feeds, per revolution of headstock spindle Length overall Width overall, incl. motor, cross slide fully axtended Bench lathe with standard equipment (less motor) Set of three Raising Blocks Chip Tray Stand Motor, switch and wiring, three phase Motor, switch and wiring, single phase 8'(9'5 mm) *' (5 mm) *' (5 mm) 8'dia. I T.P.l. Acme form 840-48 R.P.M. 1000-58 R.P.M. motor, 50 cyr:les A.C. motor, 60 cycles A.C. 8-40 T.P.r. O.20-3.50 mm 0.01-0.0037, 0'25-0.09 mm 35*' (910 mm) app.26' (660 mm) 117 lbs. (53 kgs.) 10* lbs. (a.9 kgs.) . 11 lbs. (5 kgs.) 55 lbs. (25 kgs.) 23 lbs.

(10.5 kgs.) 55 lbs. (25 kss.) 23 lbs. (10.5 kss.) 25 lbs. (11 .5 kss.) STANDARD EOUIPMENI' Primary belt, headstock belt and ch-angewheel guards, two vee belts, motor pulley 8" bore, faceplate with driver peg (for use ;llso as catchplate), No. 2M.T. soft centre for headstock, No. 2M.T. hard centra for tailstock, 2 double ended spanners, 3 hexagon keys, oil gun and thread dial inrlicator. ... FULL SET OF 15 CHANGEWHEEL{ and Drive Unit.

Page 2

THE NEW MYFORD ML1O LATHE The ML1 0 lathe is equally suitable for bench or stand mounting. The standard equipment included with the machine is extremely comprehensive and includes guards and a range of changewheels for screw cutting and fine feeds. The range of additional equipment is extremely wide, thus ensuring versatility and includes steadies, four tool turret, plain and swivelling vertical slides, angles plates, vee blocks, chucks, collets. die holders, turning tools and so on. The Myford quick setting lathe tools in 3" size (No. 108) can be used in conjunction with a special tool boat (No 10828) The illustration below shows the ML'l 0 lathe on stand No.

201121, with drip tray No 20/111 , raising blocks No. 2Ol1 1 8 and motor with drum type reversing switch (No 60/027 single phase, No 60/028 three phase).

Page 3

centre height between cenfres screwcutting Isthe The drive to the Ieadscrew The thread dial indicator is nrounted on the hand traverse shalt and is included in the standard equipment with each machine. lt is a valuable adjunct to the machine not only when screwcutting but also {or flne self-act teed s, to s h ow th e c orrect nr o nre nt fo r engagenrent of the clasp-nut. is by accurately cut changewheels protected The tailstock is provided with a gib strip to ensure nrainterrance of the a ignnrent when the quick acting clarrping lever s released.

Adlusting screws iacilitate set- over for taper turnirrg and a lever clantp rs provided for barrel clanrping, fixing point {or quick re- by a guard having a single nroval. A fork cast on the extra stud for an inter- headstock provides for an threads and,when required, nrediate gear ior left hand tailstock. for fine {eeds towards the A chart inside the guard covers a range of inch and nretric pitches, though extra change- wheels are required for trains shown give right the latter. All the gear wards the headstock. hand threads or feeds to-

Page 4

'I h.p.,1425 r.p.m. motor with drum type switch and wiring. 60/027 Single phase. 60/028 Three ohase. 20 1 18 Set of 3 raising blocks. 20/1 23 Set of leadscrew clutch parts 20/1 1 7 Steel drig tray with drain plug.' C. 67 1 Plain vertical slide, lor cross-slide mounting. Tabte 5i"-21", micrometer dial graduated 001" divisions. A, 4" 3-jaw G S chuck with threaded body. Standard pattern, 40i003 oattern, 40 004. Griptru D. 68'2 Swivelling vertical Table 5" 4", dial graduated slide for cross-slide nrountino 001 " divrsions jaw width l:", maximunl B. 4" 4-iaw independent chuck fitted backolate, 40 046 E. Machine vice No 71 opening 1 +".

c {s No.170 plain and 171 vetdrill pads made to fit on No.155 hollow centre. Centres. No.2 M.T.7511248ha.d,8'1249 soft, 153 square, 154 hall, 155 hollow, 186'l wood prong, &'169 fluted. F {^1 tD 'G&& tP # #-miilh'gl F. 20/119 Fixed steady, l:" dia capacity, for bed mounting. G. 201120 Travelling steady, 1:" dia. capacity, for saddle mounting. 201122 Fou tool turret, 8 positions, takes l" square cuiter bits. Angle plates: No.70,3"x'li"\1+" No.227,4"t2!"x2" No 2278, 6" > 21" \ 2" H. No. '1031 collets, No. 2 M T , sizes *" to +" and 2 to 13 mnr. l. No. 1438 nose piece. (Also required No.1439 closing tube), J. No. 1484 case, holds 16 collets plus Nos.1438 and 1439 L. No. 86 faceplate clanrps.

sel ot 4, 2+" long. @ K. No. 85 carriers, sizes i", i" and 1". M. No'1434 adaptor, No. 2 M.T., to enable headstock chucks, etc.,to be mounted on tailstock. L Cl. Tailstock die holders with No.2 M.T. shanks. No. 1435 for lt"dia. and No.'1436 for 1" dia. dies. il, No. 1133A arbortor *" bore milling cuttersfor use between centres, P. No. 1495 dividing attachment shown mounted on No. 68r'2 vertical slide, for all numbers up to 50 and even numbers uD to 100 except 88. Extra plates No. 1471 cover remainder uo to 1 00. O. Vec bfocks. Irlo. 73,3' X 1+" x 1|'; No.74,4'x 2" x 1+ . S. Chuck backplates; {or range available see price list. R.

No.6335 parting tool holder, with one blade lz" x iz", and key. T. Teeboltsandnuts, 1196,6"and'l'l97,3"long;alsoNo.2422forsecurino No 71 vice to cross-slide. etc. V. No.'108, quick setting lathe tools, H.S.S. butt welded "!" sq. using MA108ZB tool boat. U. Orill chucks with No. 2 M.T. shank. 40/001 0-;" and 40i002 0-+". W, H.S.S. slideresttools: No. 105 set of A, ,t"sq ;No 1478 set ol 12, *"sq and No 1115 set of 12, t" sq. w Prinrad in Fnclanrl to chon!. without notice l,lurt.otions not bineiinpin detqil

Page 5