Super Micro PDSML-LN1+/LN2+/E+ Motherboard User Manual PDF (EN)

PDSML-LN1+ PDSML-LN2+ PDSML-E+ USER’S MANUAL Revision 1.1a

Стр. 1

The information in this User’s Manual has been carefully reviewed and is believed to be accurate. The vendor assumes no responsibility for any inaccuracies that may be contained in this document, makes no commitment to update or to keep current the information in this manual, or to notify any person or organization of the updates. Please Note: For the most up-to-date version of this manual, please see our web site at www.supermicro.com. Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product described in this manual at any time and without notice.

This product, including software, if any, and documentation may not, in whole or in part, be copied, photocopied, reproduced, translated or reduced to any medium or machine without prior written consent. IN NO EVENT WILL SUPER MICRO COMPUTER, INC. BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL, SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN PARTICULAR, SUPER MICRO COMPUTER, INC.

SHALL NOT HAVE LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH HARDWARE, SOFTWARE, OR DATA. Any disputes arising between manufacturer and customer shall be governed by the laws of Santa Clara County in the State of California, USA. The State of California, County of Santa Clara shall be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for all claims will not exceed the price paid for the hardware product. FCC Statement:

This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reason- able protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the manufacturer’s instruction manual, may cause harmful interference with radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case you will be required to correct the interference at your own expense.

California Best rnia Best Management Practices Regulations for Perchlorate Materials: This Per- chlorate warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlo- rate” WARNING: Handling of lead solder materials used in this product may expose you to lead, a chemical known to the State of California to cause birth defects and other repro- ductive harm. Manual Revision: Rev. 1.1a Release Date: January 30, 2009 Unless you request and receive written permission from SUPER MICRO COMPUTER, INC., you may not copy any part of this document.

Information in this document is subject to change without notice. Other products and companies referred to herein are trademarks or registered trademarks of their respective companies or mark holders. Copyright © 2009 by Super Micro Computer, Inc. All rights reserved. Printed in the United States of America

Стр. 2

Preface Preface About This Manual This manual is written for system integrators, PC technicians and knowledgeable PC users. It provides information for the installation and use of the Intel® Xeon ® 3200/3000, Core™ 2 Duo Series, Pentium ® D (Dual-Core), Pentium PDSML-LN1+/PDSML-LN2+/PDSML-E+ motherboard. It supports single 4, and Celeron ® D LGA (Land Grid Array) 775 Processors at system bus speeds of 1066/800/533 MHz. The processor is housed in a Flip-Chip Land Grid Array (FC- LGA4) package that interfaces with the motherboard via an LGA775 socket.

The PDSML-LN1+/PDSML-LN2+/PDSML-E+ also supports Intel Hyper-Threading (HT) technology, EM64T technology, Enhanced Intel SpeedStep ® Technology (EIST) and Matrix Storage Technology. Please refer to the motherboard specifi cations pages on our web site (http://www.supermicro.com/products/motherboard/) for updates or visit Intel's web site for processor support. This product is intended to be installed and serviced by a professional technician. Manual Organization Chapter 1 describes features, specifi cations and detailed information about the motherboard and the chipset. Chapter 2 provides hardware installation instructions.

Read this chapter when installing the processor, memory modules and other hardware components into the system. Chapter 3 describes troubleshooting procedures for the video, the memory and the system setup stored in CMOS if you encounter problems. running the CMOS Setup utility. Chapter 4 includes an introduction to BIOS and provides detailed information on Appendix A and Appendix B list BIOS POST Error Codes and Messages. Ap- pendix C provides Software Installation Instructions. Conventions Used in the Manual Special attention should be given to the following symbols for proper installation of the components and to prevent damage done to the components or injury to yourself: Danger/Caution:

Instructions to be strictly followed to prevent catastrophic system failure or to avoid bodily injury. Warning: Important information given to ensure proper system installation or to prevent damage to the components. Note: Additional Information given to differentiate various models or to ensure correct system setup. iii

Стр. 3

PDSML-LN1+/PDSML-LN2+/PDSML-E+ User’s Manual Table of Contents Preface About This Manual ...................................................................................................... iii Manual Organization ....................................................................................................iii Conventions Used in the Manual ..................................................................................iii Chapter 1: Introduction 1-1 Overview ......................................................................................................... 1-1 Checklist .....................................................................................................

1-1 Contacting Supermicro ............................................................................... 1-2 PDSML-LN1+/PDSML-LN2+/PDSML-E+ Image ....................... 1-3 PDSML-LN1+/PDSML-LN2+/PDSML-E+ Layout ....................... 1-4 PDSML-LN1+/PDSML-LN2+/PDSML-E+ Quick Reference ........ 1-5 Motherboard Features ................................................................................ 1-6 Intel 3000/3010 Chipset: System Block Diagram .................................... 1-8 1-2 Chipset Overview ...........................................................................................

1-9 1-3 Special Features ........................................................................................... 1-10 1-4 PC Health Monitoring ................................................................................... 1-10 1-5 ACPI Features ............................................................................................... 1-11 1-6 Power Supply .................................................................................................. 1-12 1-7 Super I/O ........................................................................................................ 1-13 1-8 Intelligent Platform Management Interface (IPMI) ..........................................

1-13 Chapter 2: Installation 2-1 Electro-Static Sensitive Devices ..................................................................... 2-1 2-2 Processor and Heatsink Installation ............................................................... 2-2 2-3 Mounting the Motherboard in the Chassis ..................................................... 2-5 2-4 Installing DDR 2 Memory .............................................................................. 2-6 2-5 Control Panel Connectors/IO Ports ................................................................. 2-8 A. Back Panel Connectors/IO Ports ................................................................. 2-8 B.

Front Control Panel ...................................................................................... 2-8 C. Front Control Panel Pin Defi nitions ............................................................. 2-9 NMI Button ............................................................................................... 2-9 Power LED ............................................................................................... 2-9 HDD LED ................................................................................................. 2-10 NIC1/NIC2 LED Indicators .....................................................................

2-10 Overheat/Fan Fail LED ............................................................................2-11 Power Fail LED .........................................................................................2-11 iv

Стр. 4