Ramsey Electronics · RI1 · 14 pp.

Ramsey Electronics RI1 Relay Interface Kit Manual & Assembly Guide PDF

Related manuals

Document text

RELAY INTERFACE Ramsey Electronics Model No. RI1 The RI1 makes it simple to connect almost any digital output to lights, motors, or any other electrical devices that require load switching of up to 240 Volts AC or DC and 10 Amps of current! It takes a digital low (0.5 VDC or less) and high (+1 to +12VDC) and provides relay contact closures (SPDT) that can be either active high or active low. The RI1 can be interfaced with the TS1, VS1, UT5, TT7, TD1, ICI16, RF Wireless Link Modules, BD416, OII1, MD3, and WTS1. It also works with many Velleman digital products, and has millions of additional real world applications!

 Interfaces many hobby kits with real world applications  Connects a SPDT Relay to almost any digital output  Switches up to 240 Volts at 10 Amps  Digital Low RI1  1 RI1  1

Page 1

PARTIAL LIST OF AVAILABLE KITS:

RAMSEY TRANSMITTER KITS FM10A, FM25B, FM30, FM Stereo Transmitters FM100B, FM35 Professional FM Stereo Transmitters AM1, AM25 AM Broadcast Band Transmitters RAMSEY RECEIVER KITS FR1 FM Broadcast Receiver AR1 Aircraft Band Receiver SR2 Shortwave Receiver SC1 Shortwave Converter RAMSEY HOBBY KITS LBC6K Laser Beam Communicator SG7 Personal Speed Radar SS70C Speech Scrambler/Descrambler TT1 Telephone Recorder LLS1 Laser Light Show MD3 Microwave Motion Detector LEDS1 LED Strobe Light BE66 Blinky Eyes Animated Display LTS1 Laser Trip Sensor ICI1C Infrared Switch Control Interface RAMSEY AMATEUR RADIO KITS HR Series HF All Mode Receivers DDF1 Doppler Direction Finder Kit QRP Series HF CW Transmitters and QAMP Power Amplifie CW7 CW Keyer RAMSEY MINI-KITS Many other kits are available for hobby, school, scouts and just p kits are always under development.

Write or call for our free Ram RI1 Relay Interface Ramsey Electronics publication No. RI1 Rev 1.2a First Printing: June 2009 COPYRIGHT 2009-2010 by Ramsey Electronics, Inc. 590 Fishers Station Dri York 14564. All rights reserved. No portion of this publication may be copied or the written permission of Ramsey Electronics, Inc. Printed in the United States RI1  2

Page 2

RI1 RELAY INTERFACE TABLE OF CONTENTS Introduction .......................................... 4 Theory of Operation ............................ 4 “Learn as you Build” ............................ 6 Parts List ............................................. 7 Parts Layout Diagram ......................... 7 Schematic Diagram ............................. 8 Assembly Steps ................................. 10 Setup and Testing ............................. 12 Troubleshooting ................................. 12 Specifications .................................... 14 Warranty ............................................ 15 Ramsey Publication No. SHA2:

Manual Price Only $5.00 INSTRUCTION MANUAL AND ASSEMBLY STEPS FOR RAMSEY ELECTRONICS, INC. 590 Fishers Station Drive Victor, New York 14564 Phone (585) 924-4560 Fax (585) 924-4555 www.ramseykits.com RI1  3

Page 3

I NTRODUCTION The RI1 is designed to provide a simple practical interface between different types of electronic circuits. The output is a high current, normally-open/ normally-closed set of dry contacts. The input signal can be nearly any type of logic level or other voltage level between 0 and 12VDC. Input level pull- up, pull-down, and current limiting resistors are available if required. The RI1 may be configured so that either a low (active low) or high (active high) level input signal will active the output relay. THEORY OF OPERATION Note: It will be helpful to reference the schematic in the center of this manual while reading this section.

For the RI1 a low is anything below 0.5VDC and a high is above 1VDC. Active low means when the input applied to J3 “INPUT” pin is at a low level, 0.5VDC or less, with respect to ground, (J3 “GND”), the output relay, K1, will be energized. An active high means when the input signal is high, above 1VDC, relay K1 will be energized. A 12VDC power source must be applied to J1 or J2 to operate the RI1. Resistor R4 is an optional pull-down resistor and will not be required for most applications. Active Low Input Operation: For this discussion R1 will be replaced with a jumper wire and jumper JMP1 will not be installed.

Resistors R1 and R2 are dependant on the specific requirements of your application and will be addressed throughout this discussion. The input signal is connected to the J3 “Input” pin, which is connected to the base of Q1. When the input signal is low (less than 0.5VDC) the base of Q1 is taken low, which causes Q1 to turn off. This makes the collector of Q1 high. The high on Q1’s collector is connected to the base of Q2, which turns it on. When Q2 is turned on, current flows thru relay K1, closing its normally open contacts, which are connected to J4 “N/C” pin and “COM” pin.

When the input signal is high (1VDC or more) Q1 will be turned on, thus applying a low level to the base of Q2, which then turns Q2 off, de-energizing relay K1. This closes the normally closed contacts of K1 connected to J4 “N/ C” pin and “COM” pin. If the input signal is supplied by an open collector device, R2 must be installed in order to provide the high level applied to the base of Q1. This is the norm for logic devices with “open collector” outputs. If the input is able to supply the required high level, R2 should not be installed—however R1 must be installed to prevent damage to Q1.

This is normally the case with CMOS logic devices, and you should build your kit this way if you are using any type RI1  4

Page 4