• Using the Effects An integral part of the Super JD's sound is its tremendous multi-effects processor. Any Patch can use up to 8 effects at one time. The effects are divided in to two Groups, A and B. Group A includes Distortion, Phaser, Spectrum EQ, and an Enhancer. Group B features Chorus, a Stereo Multi-Tap Delay, and Reverb. The delay has been expanded to 3000ms, and will sync to MIDI clock. Two effect Parameters can be controlled in real-time via MIDI. • Using the Oscillator Sync Function This function lets you create interesting effects by forcing any waveform to be “slaved” to any other waveform in a Patch.
Any Tone (waveform) within a Patch can be designated the “master.” Each remaining Tone can then be slaved to the frequency of the "master". Pitch envelopes can be applied to the "slave" Tone(s) to try to force them out of tune, creating new harmonics and resulting in the characteristic Sync sound. This effect only works when Solo is ON. Also, the Tone switch for the selected Master Tone must be turned ON. To setup Effect control via MIDI: 1) Press PATCH. 2) Select PATCH I-15 DistSynChorus. 3) Press EFFECTS. 4) Press F2 FX Control. 5) Choose your control Source. This is the controller you will transmit from your keyboard or sequencer. 6) Choose a Destination for your controller.
7) Set the desired depth of effect. 1) In Patch Play mode, select a Patch to edit. 2) Press F1 COMMON. 3) Press F2 Key FX. 4) Press CURSOR DOWN to Switch. 5) Use the VALUE dial to turn SOLO Switch ON. 6) Press CURSOR DOWN to Sync Master. 5) Use the VALUE dial to select a master Tone. 6) Press EXIT. 7) Press F2 WG. 8) Press F1 Wave. 9) Press CURSOR DOWN to Sync Slave SW. 10) Press TONE SELECT to select a Slave Tone. 11) Use the VALUE dial to turn the Sync Slave Switch ON. 12) Repeat steps 10 and 11 for the remaining Tones as desired. 13) Press EXIT. Note: Your destination Effect must be enabled under F4 Group A and F5 Group B.
• Assigning Outputs The JD-990 has four pairs of stereo outputs to which any of the eight multitimbral parts can be assigned in Performance mode. By panning a Part all the way to the left or the right, you can effectively assign each Part to its own output. To assign a Part to a Stereo Pair: 1) Press PERFORM. 2) Press F4 Out & FX. 3) Cursor down to bottom row. 4) Cursor left or right to the desired Part. 5) Turn dial to select D-1, D-2 or D-3. • Use a JD-800 to edit Patches Each of the edit sliders on the front panel of the JD-800 can be used to edit the Tones in the JD-990 in real-time. 1) Press SYSTEM. 2) Press F4 RX MIDI. 3) CURSOR to RX EXCLUSIVE. 4) Use the VALUE dial to select ON-2.
5) Turn on the TX EDIT function in the JD-800 MIDI Menu. 6) Use the edit Sliders on the JD-800 to alter the JD-990 Tones in real-time. Now pan the Part hard right or left within the stereo pair for individual outputs. 6) Press F2 (Part). 7) Press F6 Palette. 8) Cursor to Pan for the desired Part. 9) Dial to L50 for “hard left” or R50 for “hard right". If you are using a stereo Patch, each Tone must be panned to the center for these settings to take effect. From the Patch mode, press F4, cursor to Pan, and set all 4 Tones to "0". If the appropriate edit window is open in the JD-990, the graphic display will show your changes as you make them.
Make sure the correct Tone Switch is enabled for the parameter you are editing. TBS11 © 1994 Roland Corporation U.S., 7200 Dominion Circle, Los Angeles, CA 90040 Faxback # 20013 12/95 NQPSMTR® &FA6C &J?E96D:K6C @5F=6