ROLAND — Back Cover

Mix Down (continued) 8) Press REC followed by PLAY to record your mix to Tracks 7 and 8. 9) Press STOP when the song is finished. NOTE: When creating a CD, the song length is set by the length of the mix down tracks (7-8). You may need to cut data on your Tracks to avoid empty space. ••• ROLAND VS-CDR-S2 TURBO FACTS ••• VS-CDR-S2 is a complete hardware/software bundle that provides V-Xpanded users the ability to burn audio CDs directly from the VS-880 without any additional hardware. Users can now record, edit, mix, apply effects, and master to CD entirely in the digital domain.

The included CD-R drive will also function as a CD Rom player and writer for both Macintosh and IBM compatible computers. The VS-CDR-S2 package consists of the following: • ZIP ™ disk containing VS-880 CD recording software Version 3 • Multi-session 2x write/6x read CD-R drive • Adaptec Toast CD-R software for Macintosh • Adaptec Easy CD Pro CD-R software for PC platforms • SCSI cable and active terminator • 2 Blank CD-R discs • Creating CD Markers (Track IDs) The VS-CDR-S2 allows you to create a CD one song at a time. It is also possible to use one long song with special markers to indicate the Track ID numbers between songs.

When using a VS-880 project that contains multiple songs, it is necessary to create a track ID number for each song. Use the following procedure: 1) Advance the VS-880 to the location you would like to use as the beginning of the second track on your CD. NOTE: The VS-880 will automatically use 00h00m00s00f as the first CD Track ID. • Install the Update (Requires VS-880 V-Xpanded 2.0) The installation procedure requires the VS-880-S2 Expansion disk and an external SCSI Iomega  Zip drive. Before performing the update, make sure the Zip drive and VS-880 are turned off. 1) Connect the Zip drive to the VS-880 with a SCSI cable. Make sure the termination switch on the drive is set to On.

2) Insert the VS-880-S2 cartridge into the drive and turn it on. 3) Turn the VS-880 on. 4) After scanning the SCSI buss, the VS-880 display will read “Update SYS PRG?” Press YES/ENTER. 5) “Please Reboot OK” will be displayed. Turn the VS-880’s power off. 2) Hold SONG and press TAP to create a CD marker. NOTE: In order to comply with audio CD standards, songs must be at least 4 seconds long. 3) Advance the VS-880 to the location you would like to use as the beginning of the next CD track. Hold SONG and press TAP. Repeat this procedure as desired. • Setup 1) With all equipment turned off, connect the SCSI port of the CD-R drive to the SCSI port of the VS-880.

2) Attach the terminator to the remaining SCSI port on the CD-R. If you are using multiple SCSI devices, connect them to the CD-R drive and terminate the last device in the chain. 3) Set the ID numbers of each SCSI device so that they do not conflict (the VS-880 defaults to SCSI ID #7). 4) Turn on the power in the following order: CD-R drive, VS-880, audio equipment. • Writing a CD Use the following procedure to create a CD: 1) Insert a blank CD-R disc in the CD-R drive. 2) Press SONG until “SNG CD-R Write?” appears in the display and press YES/ENTER. “Write+Finalize” will be displayed. NOTE:

When writing individual songs to a CD, use the Write function instead of Write+Finalize mentioned above. When you have completed all the tracks for your CD, use Finalize to make the CD playable on a normal CD player. 1) Press YES/ENTER. 2) Press the CH EDIT button for the track to be written to the CD-R as the left track. 3) Press the CURSOR RIGHT (>) button. 4) Press the CH EDIT button for the track to be written to the CD-R as the right track. NOTE: The disk space required will appear under the “Measure Beat” portion of the display.

Make sure that this number is smaller than the number under “SYNC MODE SCENE” (the amount of free space on the internal IDE hard drive) and “REMAINING TIME” (the amount of free space on the CD-R disc). • Mix Down The VS-880 CD recording system allows you to designate 2 source tracks to provide the audio for your CD. The VS-880 song must be mixed down (including Auto mix, EQ and effects) to 2 tracks before you create your CD. Use the following procedure to create a mix down of Tracks 1-6 on Tracks 7-8: 1) Hold SHIFT and press SELECT so that INPUT>TRACK mode is selected. 2) Hold SHIFT and press CH EDIT 1.

3) Press CH EDIT 7 and use the VALUE DIAL to select “MIX-L.” 4) Press CH EDIT 8 and use the VALUE DIAL to select “MIX-R.” 5) Press CH EDIT 1. Use the RIGHT PARAMETER (>>) button to select the “Mix Sw=” display and use the VALUE DIAL to select “PstFade.” Repeat for tracks 2-6. 6) Set the Track Status buttons for tracks 1-6 to green (Play) and tracks 7 and 8 to flashing red (Record Standby). 7) Use the faders to adjust the levels of tracks 1-6 as desired. 5) Press PARAMETER RIGHT (>>) so that “SNG CD-R Write Sure?” is displayed. 6) Press YES/ENTER. “Obey Copyrights?” will be displayed. Read the license agreement (p.61 in the VS-CDR-S2 Owner’s Manual).

Press YES/ENTER and the VS-880 will begin to write data to the CD-R. TBS69 © 1997 Roland Corporation U.S., 7200 Dominion Circle, Los Angeles, CA 90040 Faxback # 20067 11/97 NQPSMTR )&%& )& 45 HC:E:?8 DJDE6>