SC815 Chassis Manual Appendix B: BPN-SAS-815TQ Backplane Specifications JP29 B-7 Front Jumper Locations and Pin Definitions JP18 This backplane can utilize I 2 C or SGPIO. I 2 C is the default mode and can be used without making changes to your jumpers. The following information details which jumpers must be configured to use SGPIO mode or restore your backplane to I2C mode.
I 2 C and SGPIO Modes and Jumper Settings REV 1.00 SAS815TQ S UPER R JTAG UPGRADE JP29:9071 RST JP18:BUZZER RESET JP46 R144 JP29 JP18 JP42 JP33 JP34 JP40 JP51 MH2 M46 M9 M15 JP10 +5V GND GND +12V #3 #0 J8 +5V +12V +5V +12V J9 J10 JP26 JP47 #2 J7 #1 J6 J5 D3 JP44 SIDEBAND 2 I C ACT0 ACT1 ACT2 ACT3 ACT IN JP40 I 2 C Setting (Default) JP40 JP51 JP33 JP34 JP42 JP33 JP34 JP42 Jumper Jumper Setting Note JP50 2 I C #0 J5 SIDEBAND MH2 M46 M9 M15 Controller ID JP44 JP26 ACT0 ACT1 ACT2 ACT3 ACT IN Backplane ID I 2 C Reset SD OUT Figure B-3.
Front Connectors and Jumpers Backplane ID SDIN Explanation of Jumpers Connector Pins 3 2 1 I 2 C Reset To modify the operation of the backplane, jumpers can be used to choose between optional settings. Jumpers create shorts between two pins to change the function of the connector. Pin 1 is identified with a square solder pad on the printed circuit board. Note: On two pin jumpers, "Closed" means the jumper is on and "Open" means the jumper is off the pins.
SGPIO Setting Note Jumper Controller ID 3 2 1 Backplane ID I 2 C Reset SD OUT Setting Backplane ID SDIN I 2 C Reset B-8 Front LED Indicators JP10 +5V GND GND +12V REV 1.00 SAS815TQ S UPER R JP47 JTAG UPGRADE JP29:9071 RST JP18:BUZZER RESET #2 JP46 R144 JP29 JP18 D3 JP42 JP33 JP34 JP40 JP51 SIDEBAND MH2 M46 M9 M15 #3 #0 J8 +5V +12V +5V +12V J9 J10 JP26 J7 #1 J6 J5 JP44 2 I C ACT0 ACT1 ACT2 ACT3 ACT IN JP18 JP18:BUZZER RESET *The buzzer sound indicates that a condition requiring immediate attention has occurred. Overheat or Drive Failure LED D3 #1 J6 The buzzer alarm is triggered by the following conditions: Figure B-4. Front LED Indicators 1. Hard drive failure Front Panel LEDs 2.
Fan failure Specification 3. System temperature over 45є Celsius. Overheat or drive failure B-6 B-7 JP33 JP34 Pins 2-3 Pins 1-2:ID#0 JP40 Open JP42 Pins 2-3 JP50 Closed Jumper Jumper Setting JP33 Pins 1-2 JP34 Pins 1-2:ID#0 JP40 Closed JP42 Pins 1-2 JP50 Open Jumper Settings Jumper Jumper Settings Note JP18 Open: Enabled Closed: Disabled Buzzer reset* JP29 Open: Default Closed: Reset MG9071 chip reset LED State D3 On