Super Micro Computer, Inc. SC827 — Super Micro SC827 Chassis Manual PDF Download

SC827 Chassis Manual C-7 Front Jumper Locations and Pin Definitions JP57 4 FAN4 U7 BAR CODE 4 1 JP56 JP30 1 3 JP30 JF2 JP48 To P/S F13 F14 C267 4 1 FAN2 + C45 C266 4 1 FAN1 20 19 + 1 + R202 C269 F16 U3 U4 C130 J25 1 6 #D2 JP49 7 R11 10 C C DEFAULT 1-2:50 5 C OH R226 A D11 R199 FAN3 U8 C268 F15 + + C201 + C3 REV 1.01 SAS827T J22 JP30: OPEN:45 C 2-3:55 #C2 7 X1 11 U6 TP3 12 U13 HB C A D1 33 34 23 L2 U10 JP69 R40 1 2 19 + C114 C209 C115 R153 C116 1 4 D68 D65 C111 C112 C113 R152 F18 F17 C210 J12 #B2 7 C43 R144 R145 JP55 6 1 R196 JP26 U2 10 5 R113 P7:ACT#B2 P6:ACT#B1 P1:ACT#A0 P2:ACT#A1 P8:ACT#C0 P9:ACT#C1 P3:ACT#A2 P4:ACT#B0 P10:GND JP26:

C58 C19 C15 R81 + D62 C85 C28 C63 C25 R77 D57 JP54 J7 #A2 7 U1 C75 BUZZER RESET JP18 JP18 2-3:TEST 1-2:BUZZER ENABLE OPEN:BUZZER DISABLE + BZ1 R297 1 3 JP18 JF4 2 20 JF1-D 19 1 C173 JF6 JF1-CD + C199 P1:ACT#C2 JP49: P2:ACT#D0 P3:ACT#D1 P4:ACT#D2 P10:GND J24 #D1 7 7 JP65 4 1 (FAN) MB-D 1 4 F11 F12 JP47 C195 C196 F10 (PWR) MB-D C198 + C197 J16 #C1 7 7 JP60 R222 4 1 (FAN) MB-C U11 1 JP46 C193 C194 4 F9 (PWR) MB-C JF1-B 19 + R94 R82 C44 D64 C119 D59 J10 #B1 7 7 JP59 4 1 MB-B (FAN) U9 1 4 F4 F5 JP13 C34 C35 (PWR) MB-B R110 R104 F6 C18 + C57 C14 C84 R80 R79 D61 C29 R76 R75 D56 (FAN) (PWR) MB-A MB-A 4 1 JP58 J6 #A1 7 7 JP10 1 4 F2 F1 C32 C33 F3 JF3 2 JF1-C 1 C156 D72 J23 #D0 C121 Figure C-8:

Front Jumpers J14 #C0 F7 F8 DESIGNED IN USA JF1 1 2 JF1-A C20 D63 C26 C64 C24 R78 D58 J8 #B0 C21 C17 D60 C23 D55 J5 #A0 JF1-AB JF5 Explanation of Jumpers Connector Pins 3 2 1 To modify the operation of the backplane, jumpers can be used to choose between optional settings. Jumpers create shorts between two pins to change the function of the connector. Pin 1 is identified with a square solder pad on the printed circuit board. Note: On two pin jumpers, "Closed" means the jumper is on and "Open" means Jumper 3 2 1 Setting the jumper is off the pins. *The buzzer sound indicates that a condition requiring immediate attention has occurred.

The backplane buzzer alarm is triggered by the following condition: Backplane temperature over 45є, 50є or 55є Celsius, depending upon the 1. overheat setting selected. See the table above for details. C-8 Jumper Settings Jumpe r Jumper Settings Notes JP18 Open: Buzzer disabled 1-2: Buzzer enabled (Default) 2-3: Test setting *Buzzer reset JP30 Overheat Settings Open: 45º Celsius 1-2: 50º Celcius (Default) 2-3: 55º Celcius Backplane overheat settings