Super Micro Computer, Inc. SC827 — Super Micro SC827 Chassis Manual PDF Download

SC827 Chassis Manual D-6 Front Jumpers and Pin Definitions JP69 Buzzer C178 C176 CR6 D79 JP57 1 D74 + 4 FAN4 C269 F16 JP30 1 3 JP30:

OPEN:45 C 2-3:55 C C DEFAULT 1-2:50 JP30 R145 JP69 BAR CODE FAN3 C268 4 1 F15 JP56 R144 CR5 D76 D71 46 54 45 1 2 JF4 50 C42 SPI C48 C53 R67 33 34 44 TP1 TP3 TP2 R48 C39 C A D1 R64 R65 REV 1.01 SAS827B D65 DESIGNED IN USA F13 F14 CR4 C267 4 1 JP55 FAN2 + C45 D62 C28 C25 D57 C266 4 1 JP54 R142 FAN1 R216 R217 JPW3 MB-B JF2 46 54 45 1 2 + C177 C203 U44 R188 U13 R187 U43 R10 C67 R106 R12 R107 RT6 R134 R135 R85 R11 C A D11 JP18 1 3 BUZZER RESET JP18 2-3:TEST 1-2:BUZZER ENABLE OPEN:BUZZER DISABLE R51 + C167 C168 C169 + C201 + C3 51 24 47 23 F24 F25 F19 F20 F21 F22 F23 F26 MB-D 12 24 F35 11 4 12 22 23 TP5 + C114 C115 C116 JP36: OPEN:DEFAULT CLOSE:ANY POWER BUTTON CR13 1 JP36 1 JP35 JP35:

OPEN:DEFAULT CLOSE:LED TEST U37 U38 C58 C15 C19 + C85 R223 4 8 5 1 F31 F32 F33 F34 51 24 23 50 47 Explanation of Jumpers Figure D-3: Front Jumpers To modify the operation of the backplane, jumpers can be used to choose between Connector Pins 3 2 1 *The buzzer sound indicates that a condition requiring immediate attention has occurred. The backplane buzzer alarm is triggered by the following condition: Backplane temperature over 45є, 50є or 55є Celsius, depending upon the 1. overheat setting selected. See the table above for details.

D-6 BZ1C174 C175 + + C200 C199 C170 C173D7 C8 160C159 C158D73 R133 JP18 C19 C8 143 D70 D67 5111842611 R12RRR RR112382+C197 1JF6JF6-CD D69C121 D66 C171 615C7155 C15C 659934 9911 1C 789 11C FFF 2C 110C FF1 F C124 C126 C123 441256 2454 51 JF38 2J21 1DEB RU 69G 15C46C43 JC P4 I2C1T+O PSC4 D4 63C119 DD 55 89 JP36JP35 R49 C21+C84D D61 D D5 56 JPW2JF5-AB 1R22 FFFF2 22237890MB-A JF3 JPW1 F36 1F17C210 C49 C79 C80 CC7778 C18 CC5174 C29 1 JF5 JF1 RRR222011645 MB-C R224 60 5 48 5 50 2347 1 13RR220034 R53 CCC262644 C17 51 2454 2347 50 441256 optional settings. Jumpers create shorts between two pins to change the function of the connector.

Pin 1 is identified with a square solder pad on the printed circuit board. Note: On two pin jumpers, "Closed" means the jumper is on and "Open" means the jumper is off the pins. Jumper 3 2 1 Setting Jumper Settings Jumper Jumper Settings Notes JP18 1 2 Open: Buzzer disabled -2: Buzzer enabled (Default) -3: Test setting *Buzzer reset JP30 1 2 Overheat Settings Open: 45º Celsius -2: 50º Celcius (Default) -3: 55º Celcius Backplane overheat settings JP35 Open: Default Closed: LED test LED testing b JP36 f Open: Default , multiple power utton functionality Closed: Single power button unctionality Any power button JP69 FW upgrade connector