2-8 Item Thread dia.
(mm) and pitch (length) Torque value N.m kgf.m lbf.ft • ENGINE Mounting case bolt Mounting case nut Plug hole coil bolt Flywheel boss bolt Flywheel bolt Alternator bolt nut Alternator pulley lock nut Starter motor bolt Starter motor front bracket screw Starter motor bolt screw Starter solenoid switch screw EOP switch (Low pressure side) EOP switch (High pressure side) ECT sensor A/F sensor Knock sensor MAP sensor bolt ECM bolt Intake manifold bolt, nut Exhaust manifold bolt Exhaust guide bolt Water separator body screw Fuel strainer body screw Fuel pump (low pressure side) bolt Vapor separator assembly bolt Vapor separator stay bolt Service check bolt Vapor separator cover screw Water jacket cover screw Strainer cover screw Pump cover screw Pump harness assembly screw Float pin screw Fuel pump case bolt Plate stay A bolt M12 x 1.25 M10 x 1.25 M8 x 1.25 M10 x 1.25 M6 x 1.0 M8 x 1.25 M12 x 1.0 M10 x 1.25 M8 x 1.25 M14 x 1.5 M10 x 1.25 M5 screw M5 M6 screw PT 1／8 M10 x 1.25 M10 x 1.25 M18 x 1.5 M12 x 1.25 M5 x 0.8 M6 x 1.0 M8 x 1.25 M10 x 1.25 M8 x 1.25 M5 screw M5 screw M6 x 1.0 M8 x 1.25 M8 x 1.25 M6 x 1.0 M5 screw M5 screw M5 screw M5 screw M4 screw M6 x 1.0 M6 x 1.0 64 44 26 44 12 32 118 44 26 110 44 2.5 5 6 8 22 12 42 31 3.4 5 26 39 26 3.4 3.4 12 26 26 12 3.4 3.4 3.4 3.4 2.1 2.1 12 12 6.5 4.5 2.7 4.5 1.2 3.3 12.0 4.5 2.7 11.2 4.5 0.25 0.5 0.6 0.8 2.2 1.2 4.3 3.2 0.35 0.5 2.7 4.0 2.7 0.35 0.35 1.2 2.7 2.7 1.2 0.35 0.35 0.35 0.35 0.21 0.21 1.2 1.2 47 33 20 33 9 24 87 33 20 81 33 1.8 3.6 4.3 5.8 16 9 31 23 2.5 3.6 20 29 20 2.5 2.5 9 20 20 9 2.5 2.5 2.5 2.5 1.5 1.5 9 9 • GEAR CASE Propeller shaft holder bolt 18 mm castle nut (*1) Gear case bolt Oil level bolt Oil drain bolt Water screen screw Sensor nipple Bearing holder (LCD, XCC and XCD types only) Impeller housing bolt 64 mm lock nut Pinion gear nut M10 x 1.25 M18 x 1.5 M10 x 1.25 M8 x 1.25 M8 x 1.25 M5 x 0.8 M8 x 1.0 M100 x 2.0 M8 x 1.25 M64 x 1.5 M18 x 1.0 34 1 34 3.4 3.4 1 3 191 19.7 123 142 3.5 0.1 3.5 0.35 0.35 0.1 0.3 19.5 2.0 12.5 14.5 25 0.7 25 2.5 2.5 0.7 2.2 141 14 90 105 • EXTENSION CASE/MOUNTING CASE Extension case bolt Lower rubber mounting bolt Upper rubber mounting bolt M10 x 1.25 M12 x 1.25 M12 x 1.25 39 83 83 4.0 8.5 8.5 29 61 61 *1:
If the split pin cannot be set by tightening the 18 mm castle nuts to 1 N.m (0.1 kgf.m, 0.7 lbf.ft), tighten the 18 mm castle nut until the split pin can be set. Note that the maximum torque of the 18 mm castle nut is 44 N.m (4.5 kgf.m, 33 lbf.ft).